Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I made an own SPI device driver using the SDK's BM280 as a pattern
The result has a strange clock configuration (normally high - should be normally low)
Looking through...
Hi,
I'm trying to incorporate pc-ble-driver-js into NodeJS based server.
For some reason, after connecting to a peripheral with a custom service, although the connection...
Hello
Trying to get the idea of whether the Long Range and Direction finding could be used simultaneously with the devices capable of both features.
Googling Long Range...
What causes the "Stopped by vector catch" error? Where is this documented?
The project builds successfully, but when launching the debugger, the Output window displays ...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I am evaluating nRF Connect SDK V1.5.0 for use on a new project. (I could use the added features since V1.2.0.)
Building with Segger Nordic Edition V5.34a
I updated the...
Using the sample code from this earlier devzone post , I've been trying establish communication with from my bosch sensor to my board. I have the code running: and it's printing...
Hi,
I'm combining a SAW filter with your nRF52840 and an RF MUX. The MUX requires AC coupling capacitors. Is that required in series with the SAFFB2G45MA0F0A as used on...
Are there software development tools/libraries for Mac/PC/IOS/Android for sending and receiving serial UART data to a nRF51822 module? I can run the nRF51822 and send and...
OS: Windows 10 64bit
SW: Segger Embedded Studio 5.10 nRF SDK 17.0.2 Softdevice S140
HW: nRF52833 2020.6
Hello,
I had found an example integrating the ble_app_uart...
Hey I'm currently trying to update the nrf9160DK_52840s bootloader through the nrf9160DK_9160 by which i mean:
-Send bootable image_52 over LTE or USB to 91
-Have a check...
Hi there,
We're in the evaluation of sending large payloads with nRF9160.
The payloads are 4-5MB in size which will come from an external flash chip.
The payloads...
Hello,
I try to upgrade my project from NRF5 SDK 15.3 to 17.0. I like to begin with the bootloader, therefore I followed the steps from
https://infocenter.nordicsemi.com...
Hi,
I'm playing 52832 ble_app_hrs_c Central example with latest SDK 17.0.2 and SD7.2.0.
The wierd thing is that after the service discovered, next enable cccd. But nrf_ble_gq_item_add...
