Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I tried to build the ble_app_uart example for nRF52820/s140. In my project I need to use C++ modules.
My usual approach that worked so far:
Take an example project...
Dear Nordic Semiconductor-Team and everyone else, thank you for helping the thousands of people in this forum an answering their questions thoroughly. I have a question/problem...
Hi,
I have to program the application on an nrf52840 chip that is connected to another MCU via the SPI interface. Since I have to send the image from the MCU to program...
Hi, I am building an application on the nrf5340dk using using nrf5340dk_nrf5340_cpuappns as the target board.
When I have CONFIG_NETWORKING=Y enabled in my prj.conf I am...
What causes NRF_LOG to report 'overflow' ? The buffer I provide is certainly large enough.
I have #define NRF_LOG_DEFERRED 1
What happens if I have something like this...
Hi,
When the Bootloader calculates the application CRC it takes around 350ms. I saw that it is possible to switch off the crc calculation or to use hash for validation....
Hi!
We are working on testing JIG after SMTA process and we'd like to use open source solution for in circuit flashing and testing our product. Project is based on NRF52832...
I am using a nRF52832 custom board based on SDK11 and SD 4.0.2 configured as a peripheral with a GATT server. I am seeing a case where the client is an Iphone XR iOS v13.2...
Hello, I'm struggling programming the Blinky app from examples to my NRF52 DK (pca10040) Here is my script: # 1. Generate settings nrfutil settings generate --application...
Hello, I hope you are doing well.
I am using the nRF52832 with the SDK16. After adding some new custom characteristics, I didn't have enough space in the BLE_GATTS_VLOC_STACK...
Hi,
We tested, certified and declared our bluetooth product with Softdevice S140 v6.1.1 and referenced the QDID 124988 launchstudio.bluetooth.com/.../77429. On the declaration...
Hi,
We would like to share a part of our Zephyr software with a customer. We would like to share a static library, not the source code. The code to be included in the static...
Hi,
I am getting a "Cannot Create Project" error when trying to create my first project with NCS for the nRF9160 DK board. I installed the SDK using the toolchain manager...
nRF devices have a proprietary service called Nordic UART which provides a similar functionality to SPP (Serial Port Profile) of Bluetooth Classic but over BLE. Now, for SPP...
Hello,
I am using anrf9160 chip. I have a question about the ERASEPROTECT register. I would like to write it using the firmware to disable the ERASEALL functionality.
...
