Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Segger Embedded Studio always starts with license error even though a nRF52840 DK is connected.
It always complains as follows:
"
Embedded Studio could not find a commercial...
I'm getting an undefined reference to "app_uart_init". I've enabled the respective libraries in the sdk_config.h:
//====================================================...
I tried to combine the Wireless_uart example with the USB CDC example to be capable of using both but it doesn't seem to be working.
When I plug my board using the nrf USB...
Hi there,
I am using WIN10, Segger studio 4.52c and nRF SDK16.
I can successfully run ble_app_uart example on PCA10056, but when i try to run same code on fanstel EV-840...
Hi, I have been working on setting up the environment for development of nrf52840 and nrf9160 the past three days. I have nRF9160 dk which comes with nrf52840. I have been...
When I built and run your example Bluetooth: Peripheral HIDS keyboard and I saw the following errors in logs: E: set-value failure. key: bt/ccc/283926aaa86c0 error(-2) E:...
Hi,
We would like to know whether below gang programmer can be used for gang firmware flashing of NRF9160 application FW and NRF9160 modem FW.
Also we would like to know...
I am getting the following error when trying to register a nRF9160-DK with a HWID. There was an error adding your device: nRFCode 40001:
Please advise how to move forward...
Hello!
I've got a couple of NRF52832 based modules - Holyiot-17095-nRF52832. These modules are presented in the list of supported - https://www.nordicsemi.com/Software-and...
I performed below mentioned steps:
Downloaded SDK 12.1.0
Soft Device s130_nrf51_2.0.1_softdevice.hex
Built secure boot-loader with new public key
Built project ble_app_hrs...
I'm trying to compile hci_usb sample of Zephyr with Nordic Connect SDK v1.3.0 using Nordic's proprietary controller but apparently it fails.
I'm using following configuration...
Hi I'm doing the Bluetooth GATT: How to Design Custom Services & Characteristics [MIDI device use case] example ( https://www.novelbits.io/bluetooth-gatt-services-characteristics...
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer. My setup: HW: PCA10040 1.2.4 SDK: 15.3 Project: \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral...
Hi
I'm using SKD16.0.0 and S132, and I want to realize that peripherals can only connect to a center with a known MAC address through directed advertising. How should I...
Hi Folks,
I am getting in trouble with SoftDevice activation. Indeed, my application did not return from the "nrf_sdh_enable_request()" call, more precisely it hangs into...
