I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I understand that the only supported method to upgrade the modem firmware from one major version to another (e.g. 1.1.x to 1.2.x) is via JTAG. As an educated guess, I would...
To the kind attention of Nordic support team,
when I open generic_nrf52833_xxaa.emProject in sdk16 in order to compile, I get this error:
(Anyway it happens when I use...
Hi,
I'm working now with the uart connection between NRF52832 and SIM868 module, my question is:
Is there any uart interrupts implementation (examples), i want to receive...
Hi everyone,
I am in the phase of evaluating different chips and need to know the number of PWM channels for the nRF5340 and can't really find this information. The product...
Hello guys. I have six of these boards nrf52840
Do you have any Arduino Bluetooth sample code for using six or seven of these boards in a peer to peer network setup? ...
Hi , i have implemented a event to flash handler with NRF_SDH_SOC_OBSERVER and it work . But I need to know which operation is related to the event , Es: void FlashEvent_Handler...
I am trying to open HTTPS client project from \v1.2.0\nrf\samples\nrf9160\https_client i am facing below error.
I tried opening different project still i am getting same...
Hi,
I followed this thread ( Link ) to implement a simple message model on the light switch example from nRF SDK for Mesh v1.0.1. I created a "send_simple_message" function...
Hi,
Our custom NRF52840 device uses a cellular modem. We communicate with this modem using AT commands.
We will also be hooking up our devices to a custom server that...
Hello,
I have recently purchased an nrf9160-DK for a project I'm working on here in the UK. Having fired it up and realised that the iBasis coverage is minimal where can...
I'm starting to try to figure out a secure OTA process using the 9160 and tools that Nordic has provided in the SDK and I am confused by one thing I'm encountering.
What...
Hi.
I want to test my iBasis SIM card for NB-IoT with nRF9160DK. So, I tested with the "AT_client" example. I have followed "Getting Start with nRF8160 DK" instruction and...
Hi, I am trying to run ble example - uart in segger embedded studio. I am using 11.0 sdk. I have imported keil project into segger embedded studio. I have the error stating...
Hi devzone,
I'm using translation.
I use nRF52840. I created a firmware like the attached one based on the SDK15.3\examples\peripheral\bie_peripheral\ble_app_blinky. ...
