Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I was using nRF52840 ， flash is mx25L25645GM2, I used fatfs with QSPI ,but I found fatfs was unstable,After some time, the stored file would dispear.Sometime there were...
what is credit based flow control in L2CAP connection oriented channel..?
What is meaning of credits..?
what is exact usage in IPSP ..?
How it will effect data communication...
Hello,
I am preparing sniffing workspace for BT Mesh, where I have 3 devices in the Mesh network (provided by nRF Mesh app) and I need to read SRC, DST, SEQ and simmilar...
I tried to run my Thingy91 off the battery but it shuts off instantly.
My questions is if the battery charging functionality is in the firmware or hardware? Trying to figure...
Dear Nordic support member,
Where does "pca10100e folders" be installed?
I have nRF52833 development Kit. But I could not find pca10100e folder.
Note: My IDE is IAR...
Hi, I am looking to develop applications for the nRF5340. After watching the "Introduction to Zephyr RTOS" webinar, I saw that the software engineer presenting the demo was...
Hello
I am making a project in SDK v17. I want to use mpu6050 sensor but I don't know how to use library included in SDK.
The example Martinsbl has in GitHub is optimized...
Hi, i'm trying to find a way to use the Nordic nrf52840 with Adafruit SIM7000-LTE-Shield, the only apparently way is with Arduino IDE but i´m not using it (no success at the...
Various errors during medium-term deployment of cellular-enabled sensor device
We've prototyped an agricultural gas sensor based on the nRF9160, which takes readings every...
Hi,
We are having trouble getting the Thingy91 firmware running as is. We have achieved this in the past but I had made too many modifications and I decided to scrap it...
HI! I'm on Windows x86 and I've followed the steps from the getting started assistant. After trying to locate the board directory ncs/zephyr/boards/arm/nrf9160_pca10090 ,...
I am doing a custom desk for a client and I had this idea of adding a electromagnetic lock on a drawer. That is easy enough but I thought that maybe I could add a couple of...
Hello If I an exemple like ble_thread_dyn_mtd_coap_cli and that I configure the mode in MULTIPROTOCOL_802154_MODE_FAST_SWITCHING_TIMES: do you have any idea how long it takes...
I have two SPI buses on my board, with a different type of slave chip on each. Only a few bytes are read from each during boot. When I use SPIM0, 1 or 2 for them there is...
Newbie here simply trying to run some example projects from the SDK.
Setup:
Segger Embedded Studio 5.10b
Tried example projects in both SDK v17 and v16
nRF52 DK...
