Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I'm using nRF52832 + SDK17.0.0 + s132_7.0.1. I am testing buttonless DFU on the PCA10040 board based on this blog, The initial DFU (when there is no app) is successful:
...
Hi, 1) I want to run the client-mesh from DK sources into Dongle. So, I did: - modified the client-dk project: nrf5_SDK_for_Mesh_v4.0.0_src\examples\light_switch_dongle\client...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hi Support-Team,
My iOS app crashed when I updated IOS-DFU-Library from V4.6.0 to V4.8.0.
I attached the Xcode debug info and iPhone Analytics.
Thank you very much!
Hello,
Would appreciate some understanding of a compiler warning. Developing for nRF52832 using SDK 15.3.0 plus S112.
This code compiles without warning:
Then I switch...
I have tried a lot of different settings but the NRF52810 still does not output carrier..
How do I configure the radio to only send carrier for NRF52810?
Hi,
I need to stream data from NUS UART Central Device to one peripheral, but the device always disconnects while trying to send second set of data. So I changed the write_req...
Dear
I have changed light_switch server example of " nrf5_SDK_for_Mesh_v4.0.0_src" from PCA10056 to PCA10059. All function of the code works well except button.
For button...
Morning. I have a Fanstel840F module. I use attached example sketch. I flash nrf52DK with this sketch, it works fine. I can scan with NRF PC and Mobile software, and see smartTag1003...
Hi,
May i know any software utility suggestion to debug the USB data (200 bytes data) communication from device to host and vice versa for nRF52840.
Similar USB sniffer...
I think there is a bug in the west tool. If only one -Dxxxx=”xx.h" parameter in the command-line, the quotes will be filtered. So update the "nrfxlib\nrf_security\src\mbedtls...
Hello, everyone!
I am using nRF52DK and SDK v17, and I am dealing with the example of ble_app_uart.
Using this example, I am testing how buttons control BLE scanning...
Hello. I am trying to implement a application jump from my normal firmware located at memory 0x19000 per recommendations based on the soft device used (s112) to a different...
Hello,
I am working on the nrf9160 board using cloud client sample. The connection to AWS and the boards loses after running for a while. When I reset the board it connects...
