Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have latest SDK, which is nRF SDK 16.00. I have noticed that not all the examples are available for PCA 10100.
So my question is what is the difference between the PCA...
Hi,
I have compilation error to use SPI.
Checking project status Building ‘ble_app_beacon_pca10056_s140’ from solution ‘ble_app_beacon_pca10056_s140’ in configuration...
Hi,
I am trying to get the nRF-IEEE-802.15.4-radio-driver found at GitHub to run on my nRF52840 DK.
Does anyone have a check list or can explain how to link the files...
Hello,
I'm wanting to start a project with the NRF52840 DK in Segger Embedded Studio. I went through almost all of the tutorials and set up the SDK.... etc but I have...
hello.
I used 52840 act as center device.whose RX TX connected to my another MCU(MTK7688 UART). This is a IoT-GateWay. now I want to upgrade the 52840 application. BUT,...
Hi
Two years ago our device was tested using nRFgo Studio 1.21.2.10 Direct Test Mode.
How can I know if the nRFgo software used BLE 4.2 or 5.0 during the tests? The only...
Hello,
We are making a custom application where we have several ble-mesh server nodes (nRF52832), and one of them connects to an Android app, acting as a proxy. The app...
Hi All,
I want explore BLE5 extended advertisement with nRF52832.
Using "ble_peripheral\ble_app_blinky" code from SDK16.0.0, facing " NRF_ERROR_INVALID_PARAM (7)" error...
Hi, I ported the TimeSync example devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices to the current SDK 16.0.0 and S140_nrf52_7.0.1_softdevice. But...
I am unable to set the PA/LNA Mode on NRF52832 using SDK 14.2 ( Soft Device Version S132 5.0 ) using the Fansttel BT832X SoC.
i have used the exact function on the below...
There is the nRF52840 specifications sheet at the reference circuitry there is a pin 74 that is indicated as ground, what is this? 74 does not seem to line up with the method...
I don't know if this something I'm doing wrong, a Segger stupidity, or something else. I'm using SES and copied the examples/ble_central/ble_app_blink_c project to another...
I am struggling with excess current consupmtion using uart+fifo. It seems like ~300uA is drawn by UART and disabling via app_uart_close() doesn't help.
I have checked all...
HI,
I have nRF9160 modem DK. I am working a project based on http sample.
The LTE is initialized through the call:
w_lte_lc_init_and_connect();
But after ( in the...
