Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Greetings everyone,
I am a beginner in this and would like to ask for help in reading battery level.
Battery info: 3.7V, 100mAh, 0.37wh.
I have tried to read on the...
hai ,
i my application i need to update ota over serial . i m using nrf52840 and sdk 15.2
step 1 : at first flashed uart boot loader code on my board
step 2 : updated...
Hello
I am testing connection between nrf51 dongle and my BLE keyboard using heart_rate_collector sample.but there is an issue with on_service_discovery_response.
my BLE...
Does exist any IC/module of Nordic which could be used as NFC reader/initiator and that has BLE integrated also?
Or just a little BLE module with on-board uFL connector...
Hi Devzone:
We are testing TX and RX range with our customized boards, and encountered a rather bizarre problem:
The connection range is pretty good indoor, maybe 20~30...
I am working on a driver for the Adesto AT25QL641 QSPI Flash Memory chip. Comparing the hardcoded nRF52840 QSPI instruction set and the AT25QL641, they are 90% identical except...
Hi,
I am trying to implement Zigbee mesh and in the Zigbee End device(ZED), I want to know its neighbor table record or routing table record. I did not found any specific...
Hi,
In my application,I have written a code based on ble_hrs sample example. When I am checking the RSSI value at the tablet at 2 meter distance I am getting -56dbm. As...
Hi,
I am planning to design my own custom PCB using the nRF52840 chip.
As I am getting started, I want to make sure all the design rule dimensions are up to the standard...
Hi All,
I am trying to design a BLE module based on the nRF52840 Configuration 6 (Only Battery) provided in the product specification document.
To get started I was using...
Hi,
I know that the S132 v6 didn't support multiple advertising sets with different advertising handles. If you want to advertise with new data or different parameters,...
Hi All,
If I am to use a Piezo Buzzer to generate sound using nRF52840 PWM:
1. any suggestion on how to design the circuitry?
I am planning to use a Murata cimponent...
Hi to all,
we are developing an application nrf52832 that use BLE and internal flash as storage.
The problem, as I wrote in the subject, is the write operation is never...
Hi,
I'm working with simple_message_model using light switch example from Mesh SDK v2.0.1, I have 4 boards nRF5832, 1 client, 1 provisioner, 1 relay node and 1 server which...
Hi
We are in process to select the nRF52840 for industrial luminar application. currently we are in a proto phase
We have an query below
1. what is the range that can...
