Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have a problem with using the FDS library.
I started by exploring the example CLI program (examples\peripheral\flash_fds), it seemed to work as expected.
Then...
Hi
I have a nRF52832-DK based central node and multiple nrf52832 based peripheral nodes implemented using a combination of ble app uart c + multilink central at the central...
Hi Guys,
I am trying to access the serial number written on MCU through software.
White strip on MCU has details such as PCA10056, 1.0.0, 2018.04, 683xxxxxx. I am trying...
The Qorvo QM14501 LNA in nRF9160 reference schematic seems to be consuming several mA of current, which is quite a lot for a GPS LNA. There are other LNA chips in the market...
Hi
When I use the nRF5_SDK_14.2.0 of nRF52832, the example is selected ble_app_uart. And the Android example is the Android_UART_Client_Bluethoot_Sensor_Nordic_CortexM4_NRF52832...
Dear team, Device - nRF52832 SDK - SDK_15.0.0 IDE - Segger Embedded studio Softdevice - s132_nrf52_6.0.0 I am doing buttonless DFU in my application. I have successfully build...
Hi,
I want to use uart. I configured two uart, uart0 and uart1. I want to read and write to one uart using APP_UART_PUT and APP_UART_GET. how it possible without uart event...
I am trying to modify tx settings in open thread but when I try to execute otLinkSetMaxTransmitPower it cannot find this function. It seems to find all others. Is this not...
Hello,
I'm using a nrf51422_xxac_s110 chip, with the 12.3 SDK. My code is based on the ble_peripheral\ble_app_uart example in the 12.3 SDK. I'm hoping you can provide some...
Hi,
We believe we have either a BT communication issue for Nordic Semiconductor ASA NRF52832-QFAB-R
https://www.digikey.com/products/en?keywords=1490-1055-1-ND
...
The comport generated by the USB CDC UART example is showing up as a comport; However when I start sending something my terminal program is crashing.
When I look in the...
I've been trying to run the LWM2M sample from here but I've been running into some issues. Leshan provides two URLs for publicly accessible test LWM2M servers, coap://leshan...
I am using RIGADO Evaluation Board 320-00050
I am using nrfutil v5.2.0 to perform DFU i am able to create DFU package and when sending the package i am facing problems ...
