Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello,
I bought a Adafruit Feather M0 Bluefruit LE, the Bluefruit LE module is an nRF51822 chipset from Nordic. I connected the Adafruit board to an accelerometer. This...
Hello, i currently evalutate LTE-M for my company and i run into a lot of trouble for starting the test. But at least i have able to do the test
I have cut a lot of code...
Hi Nordic,
It reads in devzone.nordicsemi.com/.../38040
"According to Section 8.23 in the Product Specification a logical high is between 0.7*VDD and VDD and a logical...
Although BUTTONS_ACTIVE_STATE declared as 1, the hal_buttons_init(button_event_handler) yields an event when the input sees a high to low transition in stead of a low to high...
In testing the timers on the dongle, I have made a GPIO pin be controlled by the timer triggering.
So the following has a constant time between edges:
case NRF_TIMER_EVENT_COMPARE1...
I ran into the same problem as other user one year ago (I was using Arduino Studio nad Segger Studio before), now I switched to IAR (as recommended) and as the examples are...
Using SEGGER Embedded Studio for ARM v4.20a (64-bit).
I'd like to add a new source file to a nRF9160 sample project. The menu selection Project --> Add New File is grayed...
Hi,
I had a custom nRF52832 board. I did some modifications on it. But the same code doesn't run on modified one.
Just to check, Debugging on Segger the yellow arrow(i...
I've been following the guide linked here and got to the point where PCA10090 is flashed with Hello World project. However, when executing "west flash" command, an error appears...
Developing on a custom nRF52832 board, not the Nordic nRF52 dev board, but continue to use version 15.2 of the SDK. Building and download application, but get an abort before...
Hello. I am now implementing communication to multiple peripheral devices based on the multi-roll project “ble_app_multirole_lesc”. (image1)
Central link after setting memory...
Hello,
I am developing an app for Android using the Android-nRF-Mesh Library, available here: https://github.com/NordicSemiconductor/Android-nRF-Mesh-Library
According...
Hi everyone,
I use nrf52840 DK with Segger embedded studio. I have created a project where I read several sensors data and send these data to mobile through BLE UART.
...
hi,
is it possible to use a j-link programmer like this one in the photo, to program the adafruit nrf52840 board ? is the development procedures will be same as using a...
