Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I would like to use the two UARTEs available on nRF52840 with external asynchronous chips.
I've started a new development with the last sdk (15.3.0) and would...
Hi, I am trying to flash my program with the Seggar J-Link EDU Mini JTAG/SWD Debugger on nRFgo Studio. However, it says no device detected, and when I try to recover the device...
Need to send Asset Tracker data to a different AWS site, CloudMQTT. I have located the CONFIG_NRF_CLOUD_HOST_NAME and CONFIG_NRF_PORT in the autoconf.h file. I can easily...
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
I am starting with this tutorial. I want to program...
Hi everyone,
We are investigating whether the nRF52840 can be used to carry out USB device negotiation with a host in terms of setting the maximum charging current.
Our...
I'm using the ble_app_uart as my template for Bluetooth and UART communication. I'm on SDK 15.3.0, Segger Embedded Studio and nRF52840.
I would like to send the information...
Hello,
We are facing an issue where we are having a lot of packet loss (UART nrf52832) on two sensors connected to an Android Application (Android Pie 9.0). The tablet model...
Hi!
I'm trying to implement a traditional ring buffer with the nrf_ringbuf library. I'm using nRF52840 DK with SDK 15.3.0 and SES.
I'm going to receive strings of data...
Hi all,
I am working with Thread SDK v3.1.
When I run mqttsn-client-public and subcribe to make MQTT-SN network use UDP. But it doesn't have DLTS.
In the topic : https...
Initiated west init as per nRF Connect v3.0.0 Getting Started Assistant but resulted into an error. Worked the last time I did this. Any idea what's going on? "west init ...
Hi,
I'm trying upload firmware onto the nRF24LU1+ dongle (nrf2728) from the nrfgo motherboard (nrf6310) through nrfgo studios. I have it hooked up just as described in the...
Hi,
With my mistake, the firmware in nrf52840 Dongle is none, Do you know how to get the official firmware? and how to download this firmware? if using Jlink, any pin support...
Hi All,
I have a scanner project based on nrf52840 + S140 and I saw S140 (7.0.0) seems to support nrf52811.
So I want to port existing project to nrf52811 + S140 7.0.0...
Hi, I am experiencing the nrf52832 with some testing and developing few examples.
I am using nrf5_SDK_15.3 SES. OS : Windows 10.
I am using nRF52832 only. I have seen...
When designing an NFC coil to use with the nRF32832, are there any recommendations as to the coil inductance and Q that we should target?
Being a passive design, we are...
