Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all
I want to check my nrf52840 custom certification.i need to do radio test in my custom board.They are asking direct test mode with PSRB9. I m using direct test mode...
Hi, I created a simple project using the nRF52 SDK, to which I later wanted to add BLE support. I used the ble_app_blinky example from the SDK as my starting point. The example...
I have compiled asset tracker example and it worked on 0.8.2 version of board but not on 0.8.5 board.
1) Is there anything which should be made differently in software for...
Hi, I'm trying to measure the current of my nRF9160 DK (PCA10090 v0.8.2) and have some problems. In respect to the following thread (https://devzone.nordicsemi.com/f/nordic...
Hello. Project im developing requires low power wireless encoder. NRF52832 is a really impressive chip that handles everything i need within 40uA. But I've got problem with...
hi, we delevoppe a card with a module which is use your nRF52832 IC. I check in your document information relative to IO hardware, but i didn't find any information concerning...
I am writing some code for a customer using the nrf52840.
The Softdevice asserts immediately after a call to nrf_fstorage_write().
The write address is OK, alignment...
whenever I use nrf connect desktop app in my Linux system for power profilling.
The power profiling kit doesn't start and keeps on giving the same error
There are similar...
Hello team, I'm working on system development using Mesh SDK and I have some questions so please let me know. ############### Development environment IDE : Segger Embedded...
I was able to create 2 times, Timer 1 and Timer 2.
They work when they run separately, but one stops when I try to use both of them.
I need simultaneously running two...
Please confirm the following is correct for nRF52840 (per PS v1.1)
1. The firmware doesn't have to enable internal pull-up when the pin reset is configured (it's done automatically...
Hi,
I am developing a solution with zigbee (nRF52840).
I want some end device is joined to specific router.
In the documents, if end device find more than one router...
Hi, Everyone.
I'm trying to connect nRF52 DK Board to J-link base tool.
But I can't connect.
Wires between nRF52 B/D and J-link base tool are conneted below.
nRF52...
Hi,
I am new in this area. I wanted to use the detect "signal" but it doesn't work as protected. This is my main :
I just try to detect when the detect signal is HIGH...
Hello,
i tried the getting started procedure with the NRF9160DK demo board but I cannot finish the whole procedure.
After activating the iBasis eSIM, I turn on the...
