Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello, I'm currently using the nRF52840 Dongle and i need some help. On the other hand, i have BLE ela identifiers/sensors : elainnovation.com/bluetooth-low-energy.html The...
Hello,
I am getting error -
t: 17532>, app_error_weak.c, 108, Mesh assert at 0x0002CF9E (:0)
I debugged it, it took me to the flash_manager.c - line 254 which is ...
Hi. I am working on nordic 51. My mission is sending invasive brain wave with BLE.
For catching brain's spike, they need 10k Sampling per second transmitting.
However...
I'm looking into using the RTC on the nRF52840 as a Watchdog timer. The reasons being the increased flexibility that this would provide for saving context information prior...
I get an error if I use the eddystone configuration service together with another GATT service like e.g. buttonless dfu. the following change in components/ble/ble_services...
Hi all,
I would like to realize my PCB module with nRF24L01+ and RFX2401C PA/LNA. My idea is to use a PCB antenna but I didn't have any experence in that means. Someone...
After reading the support forums a bit, and browsing the documentation, I'm not sure exactly what the purpose is of the RF switch U34 in the GPS circuit. From what I've read...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
I am trying to evaluate Fanstel BT832X SOC. I am using the ble_app_uart example...
I see that there are some simple HTTP examples in the sdk (ncs v1.0.0) but they are not as fully featured as the MQTT/S lib, is there a plan to do develop a simular lib for...
Hi,
I accidentally clicked on verify answer, is there a way to undo this?
It would be very nice if someone could still have a look at my problem, thanks.
https://devzone...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the SEGGER...
Hi All
I am now working in Channel Selection Algorithm (CSA), Bluetooth Low Energy. Basically, I would like to test both CSA 1 & 2, and also I would like to modify the CSA...
Setup:
SEGGER Embedded Studio for ARM (nordic Edition V4.18 (64 bit)
GCC
Windows 7 Professional
SDK: nRF5_SDK_15.3.0_59ac345
Issue:
In order to use the GPIO...
Eagle pcb and schematic reference designs on github are incorrect.
Reference nRF52840 pcb schematics and layouts are exactly the same for examples 2-6. I believe each is...
