I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I am trying to integrate some ble code into my project but it keeps giving me errors like:
Error[Li005]: no definition for "ble_advertising_on_sys_evt" [referenced...
While developing code for our custom board, we ran into a filesystem corruption issue with fatfs+qspi block device and multiple directories. We were able to reproduce the...
I have problems running the ble_app_uart_pca1004e_s112 on a custom nrf52810 target devivce. The custom nrf52810 target is a custom board with the Rigado BMD 330, which is...
Hi there,
Please see the video for a full run down: https://www.youtube.com/watch?v=nIeIUMutBlU
Basically, I have a perfect and verified design that's been in the...
I'm using python code based on the heart_rate_collector.py example in pc-ble-driver-py to scan for devices and connect to a peripheral device.
This all works fine, except...
I have an existing Firmware (build on Crossworks) that has correct "floor" power consumption (< 10 uA during sd_app_evt_wait() on my setup).
I migrate my code to rune with...
I am stuck with strange behavior of s140 softdevice version 6.1.0 and later for ble_app_template example on nrf52840 preview dk(pca10056).
As I am planning to remove LF...
Hello,
We need to produce a driver for the ST25R3911B NFC chip working with NRF52840.
We just need to read NFCA tags so we thought that the example nfc/tag_reader included...
Hi i am using SDK15.2, nrf52832 board.
Which function is necessary to achieve multilink in example code. I dont understand how the central is connecting multiple peripherals...
I just purchased this unit and followed the setup instructions. I did not perform any flashing. When I plug the usb into the computer the jlink drive doesn't show up in Windows...
Hello, I am not sure if this was noted before. I didn't find anything about it. This is more of a suggestion. I was looking to use Thread CLI Example to use with the pca10059...
Hi,
I am using a custom board with the nrf52810 and trying to interface with the SHTW2 sensor. The sensor has an I2C interface and hence I use the TWI peripheral for this...
Hello,
I have a question regarding BLE_GAP_EVT_CONN_PARAM_UPDATE (nrf52840, SDK 15.2).
I'm evaluating the BLE_UART example using multiple peripherals. The goal is to scan...
I have an nrf52840 that the fds_init function is returning an error 11 (NRF_ERRO_INVALID_DATA).
What would be the most likely cause of this?
The code is based on the THREAD...
