Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am following the instructions at infocenter.nordicsemi.com/.../nRF52840_PDK_User_Guide_v1.2.pdf to program a pre-compiled example (blinky).
I have two nRF52840-PDK (PC10056...
Hi, im designing a beacon based on nrf52832, but i have a question about RF section, i´m using 2450AT18B100E chip antenna, and to match it with the nrf52 i'm following the...
Hi,
Trying to investigate eddystone protocol. After compiling and uploading ble_app_eddystone example I see Eddystone BLE device in non-connectable mode.
But after pressing...
I am using NRF52840 DevKit on Ubuntu 18.04 (bionic). I have successfully compiled pc-ble-driver and hex connectivity/softdevice.
I have now download pc-ble-driver-py and...
Hi,
We develop a GPS tracking device.
Development kit shows two type antenna, an external antenna(With connector) and onboard antenna for GPS and LTE.
We won't use an...
Hi, I am using nRF52832 with sensor, nfc and Softdevice S132 v3.0.0 to advertising packets .The sensor is interfaced with nrf52832 using twi interface. I have referred examples...
Hi,
I'm using the NRF52832 QFN (DCDC) for a PCB. Regarding the antenna matching components (C3,L1) it is recommended everywhere that one must use the exact same layout as...
Hi,
We are using a logger module a lot in our projects to diagnose problems, or warn API users of misuse. Sometimes it would be handy to be able to have nrf_log macros take...
I've updated my dongle firmware to the latest (J-Link OB-SAM3U128-V2-NordicSemi 170724.bin) and used JLink to erase and then reflash with the PCA10031 hex file from the sniffer...
Does the pc-ble-driver-py support BLE4.2 security (LESC)? I am able to pair using nrf connect desktop app with the following sec params, "bond:true mitm:false lesc:true keypress...
Hello,
I am using used uart sample in:
https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples
I was able to:
-change pin locations .
-select uart port...
Hello All,
I am working on nRF51822. I used custom board in my project and this is customer requirement to use nRF51822. For reference nRF51 SDK 8.1.0 used and for programing...
I am using the publishing period functionality of the generic level client and I cannot seem to get the publishing period to stick after a power cycle. When I first set the...
Where can I report bugs and issues related to the Getting Started Assistant.
I was hoping to find something on Github, but didn't find anything obviously related.
The...
