after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
We are working with DK nrf 52840 and the sdk mesh 3.0, BT sdk version is15.2 (dimming server example).
We noticed that when nordic app(nrf mesh - android) send a generic...
Hello Nordic Support Team
I am working with nrf52832 dk board.I am using mesh sdk version 2.2.0 with nrf sdk version 15.0.0.I am working with uart coexistence example...
I updated the firmware of my Nordic Thingy 52 to the latest version 2.20 using the Android app on my smartphone. Now I cannot use anymore the standard webapp ( https://developer...
I have this problem with all the samples for the nRF9160. When I build the zephyr.elf file, I get an error saying it failed. Please see the picture below. Any idea what's...
Hi,
SDK: nRF52_SDK_12.2.0
Softdevice: Generic_Stack_S332_02.00.01.hex
TX_PIN_NUMBER: on port 25
RX_PIN_NUMBER: on port 26
In our application we are using two...
Hi, We would like to support Bluetooth 5 in an upcoming product development.
Bluetooth 5 gives us two options for an improved connection: Twice the data through put (payload...
Hi,
I am using the Thingy:52 (that contains the nRF52832) and also have evaluation board of nRF52840.
Does anyone have a recommendation for a DAC for use with one of these...
HI,
May I ask, what is the version of J-LINK officially supported in sdk 15.3? I can not find it in release note.
See.
The following toolchains/devices have been used...
The Config Model Publication Set message can be used to configure a model to periodically publish its status.
If a model doesn't support publishing the `publish_timeout_cb...
Hi,
I've added WFE\WFI to my application running on nRF52840 on my RTOS Idle Hook.
Runs fine when debugger is attached , but when debugger not attached - the application...
Hi
I have merged NUS client , NUS server and multilink examples.
It works well and no problem in functions.
Now i will make that the module(with multilink nus server...
Hi guys,
sorry but first of all I have to admit that the migration is a mess. And really do not understand why you entered nrfx and did not make a clear cut. Because saving...
Hi I want to get the peripheral address from the UART and compare with scanned peripheral addresses from the central (nrf52832) and if the received address string is of one...
I'm using a custom PCB with a Laird BL651, which contains a nRF52810.
I've been following the "Transferring Project to nRF52810" tutorial here to run one of the simple BLE...
Hi
This is in part related to my previous post on PWM signal generation on two channels that are 90 degree phase shifted. The frequency of the PWM signal generated was...
