Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear nordic,
I am new in this open thread i tested your examples its working fine. i also tested CLI example i think its working but i didn't see a response in terminal...
I have a few Bluetooth transmitters based on nRF52832. My receiver devices are mainly iOS and Android mobile devices. I'm considering of replacing them with nRF52840 for Bluetooth...
Having issue with nrf52840 interface with sim808 for GPRS connection. I am trying to interface nrf52840 with sim808 using UART. But only AT and ATD command reply i can see...
I have a custom board with an application that works fine.
But when adding a secure bootloader my board starts to act weird. I am using the RESET pin on the chip as an input...
Hi,
I developed an application for the NRF52840 development board with Mbed-OS and now I would like to get it running on the NRF52840 Dongle.
Is this even possible?
...
Good evening,
We are trying to flash the bootloader DFU debug example using 10056 ble debug example code to our nRF52840 based board.
Everytime we try to flash, we get...
Hi Nordic,
My team and I are looking to purchase the NRF52840-DK for the purpose of testing long range coded-phy for bluetooth 5.0 applications. We would like to ask if...
Hi all,
When I do some tests on chip of nrf52832,the chip sometimes receive an error packet: the crc status is ok,but the length field is random.The reference documents...
Recently i have purchased nrF51 Dongle.
Am using Windows 10 (64Bit OS) on my PC.
1. installed nrfgostudio_win-64_1.21.2_installer.msi setup for flashing
2. installed...
We have a nRF based device being connected from a nRF51 dongle (PCA10031). We use pc-ble-driver 2.2.1.
We enable notifications and then we let the device running for a...
I had a working application and was trying to add DFU functionality to it. in order to do that i needed to add a bunch of files and i am at a point where i dont knwo what...
Hi,
For our continuous integration and deployment of firmware updates for our product, we want to test firmware upgrade paths from different versions. We are building a...
Hey,
I recognize that sometimes there are dependencies between silicon, board hw and software.
Is it ok to load the RF9160 mfw-m1_nrf9160_0.6.8-alpha firmware on nRF9106...
Hello,
I'm using the LTE Link Monitor with the nrf9160 DK, and trying to test out the AT modem with the at_client sample. I'm using a Lycamobile SIM card, but the link monitor...
Hi,
How to check whether is the device bonded? What value I could check? What I want to do is to perform auto pairing request when bonding is not founded, therefore my code...
