Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
nrf52832.
SDK14.2
Segger ES V3.34a
This question is probably best suited to an android forum (possibly).
We have a characteristic which is writable. When written...
Hello,
Our unused pins, 5 and 6, are not connected. What saves more current? Pull-up or pull-down or neither? These pins will never be used and are not tied to anything...
Dear nordic,
I have some doubts in nrf52840.
1. How this VDD_nrf voltage generate?
2. Is this VDD_nrf voltage only depend on Hardware or is itany dependency in software...
In the On Off Client Model in the nRF5 SDK for Mesh 15.0.0 (nRF5-SDK-for-Mesh/models/simple_on_off/src/simple_on_off_client.c) there is a check in the client callback handler...
I try to build and test my first time SES setup on Mac for further development on an existing nRF51 project and future nRF52 project.
I use SES for Nordic V4.14 and SDK...
Hi Nordic
I am looking at legacy code in nRF24LE1 that has to be ported to a new chip, nRF52xx.
The thing that I have come across is a strange thing in the datasheet...
Hi Nordics, I wonder is there any specification on IOT. I have seen the source code on IOT at nRF5_SDK_15.3.0_59ac345\examples\iot\tcp. But I don't know how to use it. So...
Hi all,
i am using:
- nrf52832 DK (IC revision 1 -> QFAAB0)
- nrf5 sdk for mesh v 3.1.0
- nrf mesh app v. 1.2.1 running on android 5.1/ second phone android v. 8.1...
On a NRF52832 based beacon I use to sensors, a SHT3 temperature and humidity sensor and a KX022 accelerometer.
I'm using the twi_manager library as it is used in the example...
I've made an application based on the SDK 15.3.0 ' Console over Bluetooth ' example:
https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-3-0/ble_sdk_app_cli ...
Hi, I understand that the Decawave UWB modules have nrf52832 Chip in them. But we are facing BLE issues (it gets disconnected and connects). We are using a Panasonic Tab containing...
I have nRF51822 AA with SDK 12.3.0 and SEGGER SES 3.10f. I was able to run and experiment with ble_app_beacon example, fixing known SES troubles, mainly with memory sections...
Environment:
BLE Slave Module: nRF51822, s110 v6.0, based on UART over BLE application example
If a peripheral and central is getting further and further, finally they...
Hi ,
my chip is: nrf52832
my SDK is: nRF5_SDK_15.2.0_9412b96
I'd like to know how to update the value of UUID when user press the "download" button ( the down arrow...
