Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Please help, I've been struggling with this problem for a week and I want to get to the bottom of it.
I have production devices in the field based on s110 v7.1.0....
Hi,
Please help, I've been struggling with this problem for a week and I want to get to the bottom of it.
I have production devices in the field based on s110 v7.1.0....
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Using the nrfx_qspi driver, it is possible to put a QSPI memory into DPM to save power, this all works fine and well. We want to keep the memory in DPM when uninitiating the...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi,
I was wondering what are the main differences between the different libraries included in the SDK that are meant to be implementations of ring buffers. I'm talking specifically...
Hi
I am developing a product for the health care market, and we chose embOS by Segger to by our OS for the nRF52840 Based product.
I've created a project based on ble_app_uart...
I am trying to send some data from RPi , And I am using the example of NRf Uart APP.
printf("\r\nUART example started.\r\n");
while (true) { uint8_t cr; // printf(" \r...
Hello All.
I try to build a generic function that read device reg over its I2C. I take the TWI master example of Nordic.
There is need for callback function to get in...
Hi
We are using your product nRF51x22_QFN48 with a balun BALF-NRF01E3 from ST and the PA.11 antenna from Taoglas Ltd.
Do you already have this product certified for RED...
Hi guys,
We have noticed some unexpected behavior of supervision timeout in case of few fast sequential calls of connect and disconnect commands in nRF connect app with...
hi...
i am using nrf52382 segger 15.2 version , i am facing issues i couldn't able to send the data ,here i am advertising using condition if my condition satisfied start...
Hello,
I use SDK15.2, SES4.12 and custom board with nRF52840.
I have a strip of ws2812b LED's connected to my device. I've made a simple RGB animation, each frame of which...
