Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I am working on a project in which the device (nrf52832) needs to be both central and peripheral and it can transmit/receive some commands through UART to set the advertisement...
Hi ,
We are using the BL652 module with your nRF52832 chipset in our important product.
In our product the wireless connection is fundamental and we would like to test...
Hi,
I am using nrf52832 to achieve system-off with low power consumption. Nrf52832 and a rf IC communicate via SPI.
I configured a pin as the wake pin.
nrf_gpio_cfg_sense_input...
Hi, I am trying to use github.com/.../nrf52-ble-image-transfer-demo with Ubuntu 16.04 Using - gcc-arm-none-eabi-6-2017-q2-update - nRF5 SDK version 15.0.0 (nRF5 SDK version...
I use SDK 15.3.0 with the example of USB_CDC. In the example, the virtual com port transmission works only when the terminal sends a DTR signal. I need the DTR notification...
Hi
I am trying to implement DFU to my project. I have done all the steps to generate packages, private and public keys etc. My program now starts at dfu and I can upload...
Hi,
setup: nrf52840 dk, no battery installed (power comes from USB connectors), switches are in default mode (SW9: VDD, SW6: default).
Flashed open_bootloader (dfu/open_bootloader...
Hello,
I'm using S112 V6.1.1 with the Nrf52810. I get a error using sd_ble_gap_adv_set_configure() after a connection. On BLE_GAP_EVT_DISCONNECTED i try to change the advertising...
After testing the nRF9160-DK with all available samples, we decided to integrate the nRF9160 in an own new product and have now a prototype available. And of course some questions...
Hi,
I am using Mac OS and 15.2.0 SDK on nRF52832. I was trying to do BLE DFU following this link . When I was trying to push the DFU zip file, It was resulting in the following...
In following the instructions of the nRF_Sniffer_User_Guide_v2.0.pdf, I'm attempting to use Segger's J-Link software to configure my nRF-51822. The environment is a Mac OSX...
I bought the nRF9160 dev kit and I can't connect to the j-link: JLinkExe SEGGER J-Link Commander V6.30f (Compiled Mar 2 2018 17:30:55) DLL version V6.30f, compiled Mar 2 2018...
Hi ,
In the target hardware I am able to detect the Nordic chipset nRF52480 by flashing USBD application on the chipset using JLINK SWD.
Now I have query related how I...
Hi!
With the nRF Mesh 1.2.0 on Android is only possible to set not group address as publishing address.
For group address happens nothing in the app and the device....
Dear,
I tried the same code on :
https://devzone.nordicsemi.com/f/nordic-q-a/43774/simple-gpio-example---nrf9160-dk/173275#173275
and my code:
The Led1,2,3,4...
