Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have a basic queries on BLE.
"Characteristic Properties" of "Characteristic Declaration" with UUID 0x2803 has Read, Write, Notify and Indicate. At the same...
Hi
Can I think so,if subscription address is identical in multiple nodes,then they are a group?
If so:
the light_1&light_2 OnOff Server Model subscription address is...
hi,
I had the board run the following code to connect it to the cellular tower:
#include <zephyr.h> #include <stdio.h> #include <string.h> #include <lte_lc.h>
void main...
I tried to advertising eddy stone beacon from getting serial UART data. i merged 2 codes in ble_app_eddystone and uart code but one error become like
..\..\..\..\..\..\components...
Hello dear Nordic Developer and Hobbyists,
first of all I would like to thank the developer team for the nice mesh demo. It functioned well and explicates the concepts of...
Hi,
I am not getting any response from the previous ticket. Did it get accidentally closed?
Case ID: 225033
Can please someone look at it? We are in urgent need...
Hi, I have tried to run nfc example, but it doesn't working, accidentaly i have found out that if supply 3V nfc not working, but if supply 2.7V and less it works, what is...
Hi, I'm designing based on the Altium files, but I'm not an antenna expert so I would like to know if you have any antenna recommendation for a low profile, because the one...
Hi,
I'm working on nrf52832 NUS. When i connect to device with "nrf connect app" i can see the data coming from sensor. But few seconds later device disconnect.
When...
Hello
I have 3 nodes, 2 Thread CoAP servers and 1 BLE/Thread Coap client.
Let's call them THnode1, THnode2 and BLE_THnode0.
I do not know the IP addresses of any node...
Hi,
I use "printf" or "app_uart_put" function to print message to UART., how can I check "all of the data had been transmit out complete"?
Thank you,
Chianglin
Hi, I want to test sending multiple packets of data with each packet having the maximum possible size of 247 bytes. I am currently testing with nRF Connect app. When i try...
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac.
Example nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\cli\uart\pca10056.
define BOARD_PCA10059.
...
I am using nrf51822. Separately BLE and flash are working perfectly alright. But when I comment err_code = ble_advertising_start(BLE_ADV_MODE_FAST); this line flash is working...
Hello,
As per my understanding, SPP was supported by BT Classic and no more supported in BLE. I have a device, which runs SPP. It has to be connected to the BLE client....
