Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello
Our custom board has two chip configurations for BLE stack. The two chips communicate with each other through UART. Both chips are running zephyr with two chip configuration...
I'm writing an app to that talks to the Thing52 over BLE, and using this as a reference: nordicsemiconductor.github.io/.../firmware_architecture.html For Battery Services...
Hi,
We just recently bought the nRF9160_DK board and compiled and loaded the AT_Client onto the DK. We have followed all the setup instructions for the SIM card for iBasis...
The example code of beacon was used from the SDK - nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_beacon\pca10028\s130\arm5_no_packs\ble_app_beacon_pca10028_s130...
Hi experts,
Currently some issues are found in zephyr os, especially the precision of k_timer. Since the nRF51 series uses RTC as the system clock on zephyr os, the round...
I use the scheduler. All my idea is put an event in interrupt handler(timer event, gpiote event and so on) and schedule it to main loop to let app_sched_execute to handle...
Hi All,
We're designing Legacy/Coded Phy scanner based on nrf52811.
The existing softdevice that supports Coded Phy scanner is S140.
Can nrf52811 work with S140 or Nordic...
Hi,
I am struggling with recconecting to Android device. I want the project to work with iOS also.
My nRF de52832 device has got peripheral role in this project. I am...
Hi team,
One of my customer is evaluating nRF52840 running ANT networking, but they may encounter with connection distance issue and wondering if they can combine BT5 long...
Hi,
I just installed the latest nRF Mesh v1.2.1 and found that my nRF52840 DK board unable to connect,
I'm using SDK as shown below:-
nRF SDK for mesh v3.1
nRF SDK...
Hello,
I need to get access to nRF51822 pins in order to test them and connected circuits.
I have access to SWD interface only.
By attempt to read ID register (A2=0...
Hey,
I am running the ble_hid_mouse example on the nRF52832 with SDK15.2 and connected a joystick to replace the buttons commands. now i wanna use the nRF52840 as a slave...
Hello,
I'm trying to create a long range IAS ( Immediate Alert Service ) unsing long range BLE 5.
On the server software I forced the PHY to BLE_GAP_PHY_CODED. I saw in...
The 'Debug Out' on nRF52832 (and 52840?) Dev Kits only works at 3V - so won't work with a 1.8V target.
The question has been asked before, and the obvious answer given ...
