Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
If I have a nRF52832 project source code, how can I know it's SDK version?
When I try to open xxx.uvprojx by Keil 5.24.2, Keil reply one message "Error #544: Required...
Hello,
I have been working with Bluetooth Mesh SDK since few months. Recently, we came across a custom BLE module which has Laird's BL652(nRf52832) chip on it (Not the BL652...
Dear Sirs,
How to advertise with nRF52810 (peripheral mode) in order to be seen by BT4 devices (Smartphones)?
Is it necessary to make a special configuration (settings...
The current dimming example is able to control 1 LED.
If I want to have a different level for each LED (and there are 4 LEDs in total) then I need to:
#define ACCESS_ELEMENT_COUNT...
I want to trigger Google Assistant/Siri/Alexa on the push of a button. I found the HID code for the home button, but I presume long pressing this will not send anything to...
Hi,
I am developing one of the code for the radio testing & in which I need to pass or select the receiving channel and at same time need to receive the RSSI value of same...
Hello,
I am newbee to nrf52840, I need to start writing code for from scratch in keil and segger embedded studio. let me know the steps to get started.
B.R.
Gourav
I am using Windows 10, 64-bit
I am using gcc tools 7 2018-q2-update (arm-none-eabi-gcc (GNU Tools for Arm Embedded Processors 7-2018-q2-update) 7.3.1 20180622 (release...
I'm having some serious issues with the Windows 10 BLE drivers, it would seem that if you scan for anything over 2-3 hours the BLE just dies!
Anyway, I am now looking at...
Hi,
I have the FatFS example up and running with the SPI0 instance (default configuration).
Is it possible to use a SPIM instance instead or do they have some limitations...
Hello,
I have cloned the latest master repos and I am using the command line to build, compile, and flash. I have successfully built and compiled the new MQTT_simple example...
Hello,
Where is the nrf9160 in terms of certifications?
Is nrf9160 'pre-certified' yet in process or not planned for pre-certification? Which carriers are targeted by...
Hello,
While I tried to compile the project, I am facing error.
Preprocessor Definitions are
User Include Directories are
OS : Windows 10
SDK : nRF5_SDK_15...
In our product we offer the ability to scan for Bluetooth advertising messages, however obviously scanning continuously requires quite a large amount of power.
If we want...
I'd like to better understand 2 aspects of the Radio Test example. My apologies if this is a repost, but I wasn't able to find complete answers elsewhere in the forum.
1...
