Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Works
Use nRF Connect v2.6.0 on Linux to erase, program softdevice.
Works
Use Keil to program application firmware
Does not work:
Use nRF Go studio to detect...
I need to implement a simple uart protocol. most messages are fixed length (8bytes) with some exceptions.
here what I do in pseudo code, I send 8bytes and expect 8bytes...
Hi
I am trying to port an SPI driver from a project for the NRF51822 to an NRF52832 and running into a problem reading more than two bytes. We are using SPI0 (not SPIM0...
Hello,
I'm using an NRF52 DK board.
I noticed that when I change P0.27 from the default (input / not connected to input buffer) to being an input pin connected to the...
Good evening,
I had a question in respect to the exact procedure needed to read a characteristic with read permissions. I have just discovered a service i would like to...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Consider the following sequence of events:
1. `health_server_fault_register` is called, and it saves the current publish period.
2. Config server receives a message...
Building ‘Smart_Remote_3_nRF52_Firmware_nRF52832’ from solution ‘Smart_Remote_3_nRF52_Firmware_nRF52832’ in configuration ‘PCA20023-SR3_nRF52832_Product_Example’ Assembling...
Hi, Nordic,
I am using the ble_app_uart example in the SDK15.2.
I find a issue that when the device, which p_client->is_notification_enabled is already true, is disconnect...
Hi,
I just started with Nordic nRF52 DK and builded and flashed nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_gls application on Ubuntu 18.04 using armgcc toolchain...
I'm experiencing a problem with the NFC.
I'm trying to make a simple read-only tag, and I've used the NFC Text Record Example to build upon. That worked without a problem...
Just wondering if you have a desktop application that can load secure packages onto nrf52840 boards?
As far as I can tell nrfConnect for Desktop can only load a firmware...
I am using PCA10040 with S132.
I am using PCA10056 with S140.
I have a Teledyne BPA Low Energy sniffer that does not support BLE 5.0.
When using programs (e.g., Multilink...
Hi,
right now I'm trying the example with Dynamic multiprotocol examples using nrf52840 Thread and Zigbee SDK, but when I build it, for example : BLE Proximity and Thread...
Hello,
I am working on implementing the USB HAL for the nRF52840 for Mbed-OS's upcoming USBDevice feature release. I am encountering an issue where the automated test suite...
