Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I found the reference design files for nRF24LE1 from here ( https://www.nordicsemi.com/eng/nordic/download_resource/10898/2/41030525/1871 ), but I can't open them in EAGLE...
pca10059, replacing stock bootloader with Adafruit UF2, using USB dfu Hi. I currently don't have a J-Link at hand, so I tried to flash the UF2 bootloader using the stock DFU...
I want to keep both chip antenna and external antenna options on our board, what is best way to handle this for nRF24LE1 4×4mm QFN24 chip-set? Can I branch the Radio by having...
Hi,
I have a nRF52840 DK and a nRF52840 Dongle. I want to test to send binary data from one to each other using Bluetooth 5 or Nordic proprietary protocols. Are there...
Hi everyone, I am newcommer in here. I just buy one nRF52840 Dongle. I want to connect it with nRF52832 DK with ble_app_uart implemented; and open a COM port in MATLAB to...
Hi,
My application is based of ble_freertos_hrs example (SDK 14.2, nRF52832) and I need some variables to survive an assertion.
It appears that Keil has deprecated #pragma...
Hi Engineer： When I use nrf5_SDK_for_Mesh_v2.1 to debug the "light_switch" project, I always need to use a minimum of three boards (one as a provisioner, one as a client,...
I am using the nrf52832dk,i am working with the spi example for the sdk15,which pins are used for the spi protocol. I am enabling spim0.in sdk_config. h the pins number 3...
I am using NRF52832 as tags for asset tracking. I want to sense whether the asset is in movement or not as simple logical '0' or '1' response from sensor. Please suggest a...
I need sample code for the multiceiver mode. I want to send data from multiple NRF24LE1s as transmitter (to be exact 3 in number) to a single receiver. I read from the data...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
My design is 1-to-1 (one central and one peripheral). They both would use peer manager to create...
Is there any good way of supporting a button interrupt in a bootloader or is this a “bad idea”?
im afraid I have to add SoftDevice support to the bootloader and I’m not...
What is different between R7 and V3 ?
Data sheet say rev 3.3 - but that is just the rev of the data sheet
Suppliers have both R7 and R-V3 inventory
Does it make any...
I'm using the Nordic nRF Toolbox Blood Pressure Monitor "BPM" app on my phone and I have the development software running. Things work fine. However, I'm trying to figure...
