Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am trying to do USB DFU on (NRF52840 with SDK 15.2) but when i run the nrfutil command it gives an error:
command: nrfutil dfu usb_serial -pkg ble_hrs_combo...
I've setup, compiled and run the BLE Beacon project an have made some changes. Now I need to enable the UART. Simply adding UART files to the project does not work due to...
Hi
We've developed a wearable device and are changing from a rigid PCB to a full flex PCB. I want to know what adjustments is needed for RF output because of this change...
I am running an example from Mesh SDK (v2.1.1) named "ble_app_uart_coesixt". I see device in Bluetooth list, everything is ok. But I need to provision this device using my...
Hi,
I am using a Sparkfun nRF52832 dev board and SES with the Jlink mini to program it.Our project involved the ability to use the micro as a keyboard so I am playing with...
I am working with NRF52832 and S132. I have successfully captured signals with the ADC (with RTC events at a frequency of 500Hz) and synchronized them using this beacon/scanner...
Hello,
I am working on few projects involving nRF52 DK's using the nRF52 15.2.0 SDK. I would like to know which would be a more efficient and reliable way of changing...
We are considering using the nRF52832 / nRf52840 for a smart lock application with a capacitive touch keypad. Currently the product is using a Cypress Cap sense product for...
Hi,
I know that the secure bootloader uses different mac address to force services discovery however i would like to keep the same
address for both software parts as it...
Good day, I am having serious problems flashing my custom NRF5282 board. I started with Openocd, using the st-link v2 debugger and I was able to connect to the device and...
Hi,
I'm on Linux (openSuse Leap15 and Debian) and got so far that I can program nRF52832 and debug with breakpoints and local variable display with this USB breakout "BLE...
Hello!
For a project I'm working on, there is the need to use a microSD card. In the past I have used a custom FatFs port (was using SDK 6), but now I was happy to discover...
Hello,
I am using the module nRF52840 and nRF SDK 15.2.0. I would like to start a PWM, going to sleep mode and still having the pwm running.
I tried combining the pwr_mgmt...
Hello.
I have one of these dk and one thingy52 and I would like to connect them to mesh network, I read somewhere that I can use my phone as provisioner so is it possible...
Hi,
I am facing problem while building example projects given in Nordik SDK on IAR IDE.
The configuration and development libraries used are,
1. Nordik SDK: nRF_SDK...
