Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello there,
my goal is to wake up via NFC from POWER_OFF Mode (sd_power_system_off). Then right after the nfc wake up sending some information (e.g. UUID) via the NFC...
As a I2C master, I need to be able to read some data from a slave device the length of which I do not know beforehand. First byte I receive from slave is a packet type and...
Hi,
I want to estimate the battery life of my nRF52 device operating on a battery of capacity 800mAh. Device will advertise once in every 10sec with an advertising interval...
I print every 500ms. Here are the last few
timers:INFO:millis 510500, cnt 16728087
timers:INFO:millis 511000, cnt 16744474
timers:INFO:millis 511501, cnt 16760868
timers...
Hello,
I have measured the current consumption of the timer example of SDK13.0.0 with PCA10056.
With timer prescaler set at 16MHz i have 1.28 mA
With timer prescaler...
Hi, I got nRF52 DK PCA10040 device(s132) and follow the steps from devzone.nordicsemi.com/.../ to use arm-none-eabi-gcc(version 5.4) to build examples like blinky. I can successfully...
Hello,
I was wondering whether or not it's possible to achieve a data rate of 160Kbps using BLE4.2. According to what I have read on this nordic blog it should be feasable...
Hello!
I hope this question has not been asked before - at least I can't find it.
I do have an application with two vender specific services (128bit UUID's) and I want...
Hi,
i am doing ble_app_beacon code on nrf 52832 with sdk 11 and s132. the packet, its advertising should only be received by the device whose bluetooth address we are providing...
main.c ble_uart.hex
Hello,
I use nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice configuration to test the ble_uart program.
i use nrfgo Studio to load the...
Hi Nordic team,
I try to use SDK for Thread v0.10.0 cli example and run diag command, but it is disable as below
Could you tell me how to enable diagnostics module...
Hi,
I'm using nRF52840. I would use data length extension and set the MTU size to 247 when it works as peripheral. However,there would be some problem when it connect to...
