I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello
I'm having difficulty in executing an GPIOTE interrupt during a BLE connection event with the nRF51 DK. The interrupt I have works fine when the softdevice is advertising...
If I set the centrals connection intervals values higher as a specific value it won't any longer find/connect/enable notifications on my peripheral.
0x00A0/0x0050/ 400...
After running the advertising_start () function in the sample software.
I set the breakpoint by Keil MDK-ARM v5 and stopped executing.
Afterwards, reset is generated!!
...
Hi,
I am using a gpiote interrupte handle function to send a notification to the master,but I find when the sd_ble_gatts_hvx() function is used,the interrupte handle function...
I have successfully completed dfu using android app, but if anyone can help me with example program so that i can perform dfu using program instead of using toolbox app, please...
On the XLR2 chipset I am seeing that if the RTS output follows the state of the CTS input.
When I load the same firmware in a XLR then RTS does not follow CTS
Hi, I am evaluating the use of ESB(without Ack) and BLE as a possible solution for my project since i have no use of Ack and in Gazell it is mandatory to use Ack. I had heard...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I'm drawing schematic with nRF51822 internal LDO. I'm wondering what is the regulated LDO output from nRF51822. I need to connect that with peripherals in stable...
We are using ANT with the nRFgo motherboard as base station and want to broadcast a signal over the largest range possible (> 100 m) to several mobile devices using the Dynastream...
I am designing a ECG monitor device. The data rate is less than 50kbps. I was planning to use BLE for the device design. But I read some documents that say BT classic is a...
Hello,
My 10031 dongle worked perfectly up to the point where I flashed it using MCP. I was able to run simple programs such as blinky, but now I cannot revert to the previous...
I want to set up an SPI communication between nRF51422 SOC (integrated on nRF51 DK) and Arduino board. I know that it is possible since I've read it in various posts and nRF51...
Hello,
I am developing a simple app for nRF51822 which sends notification data to a characteristic with a random value. All seems to work good but while testing in-depth...
