I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi all
In my application where I'm using the Soft device 6.0, I have a simple function which is very time critical. However, this function is not called very often, but...
Hi,
Please can you send me the ble_app_uart source code as it is missing from the latest 6.1 SDK.
I have the PCA 100003 & PCA10000 boards.
Many thanks.
Hi,
In my application I use 5 devices and 1 host to communicate.
I have only a few packets to transfer so the data rate can be low (22Byte/transmission).
The devices...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
I have implemented a boot loader for DFU based on the sdk v6.1 DFU project.
After a when an upgrade is triggered within the application soft reset by the application:
...
Any idea how I can control the TX power within the Timeslot API in SDK v6 SD110 v7?
Are there something similar to "sd_ble_gap_tx_power_set(tx_power)" in the Timeslot API...
Hi All,
We are running some data throughput test on Samsung S3, Note2 & S4 with 51822 and have seen some interesting phenomena as describe below:
1> On both phones,...
Hi,
I couldn't able to program my custom board using both nrfgo Studio and keil. Actually i have two laptops with different versions of j-link driver installed, but suddenly...
Currently I am searching for s130 example code. I know it's in alpha stage, but I think it should be possible to start to experiment with it, isn't it?
In the past I've...
Hi,
I tried following code to close the ANT+ channel on channel not connected to the other ANT+ device:
#define CBSC_TX_ANT_CHANNEL 0
void ant_adv_timeout_handler(void...
We have a DFU which uses a different set of of services than the main app.
Both of them share bonding information which is create by our main app.
Once we switch to DFU...
I am trying to build a system with a single PRX and up to 5 PTX devices.
Initial development work was done with a single PTX with it's address on Pipe0 in the PRX. I have...
I have a CC2540 and CC2541 chip with me. I did figure out that both of them are working, but now I am stuck up at how to practically test if the proximity profile is working...