Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello.
I’m new to the Nordic devices and I was tasked to develop a custom board based on the nRF9160 SiP. I took the nRF9160 DK as a reference, changing it according to...
Hi,
1. I was facing issue with my nordic device saying
[02:16:46.206,481] <err> net_pkt: Data buffer (1328) allocation failed. [02:16:46.206,481] <wrn> net_conn: pkt...
Hello. In the developed BLE software, the device uses nRF52840 and uses s140 v7.3.0.
I would like to confirm the s140 nrf52 7.3.0 release notes.
A memory access fault...
I am trying to configure interrupts for two push button (namely upbutton and dnbutton) on a custom board. In the main it is just looping and the module I have is as follows...
I am running demo nrf/samples/matter/lock.
I tried to use CHIP_NUS so I set CONFIG_CHIP_NUS =y, it worked well.
After that, I wanted to make it bondable so I set CONFIG_BT_BONDABLE...
Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
Hi, we are seeing an rare issue that might be connected to PAN #57 for NRF51822 and are looking for some more info on this. I assume the underlying issue is some form of read...
Hi,
I read the document and samples of Channel Sounding for estimate distance, they are working base on the ble connection.
Imagine a scenario, if there are hundreds client...
Hi there
While doing the GMAP tests for our Bluetooth stack with the HCI UART bridge of NCS 2.7 with SoftDevice running on nRF5340 Audio DK, we've tried using the HCI LE...
Hi,
1. Seems to be a bug, how to fix this error. 2. Repeat example: ncs\v2.8.0\nrf\samples\bluetooth\peripheral_uart
Thank you for all your assistance. Kind regards...
Hello. Both toolchain/sdk are v2.8.0.
It is coding based on the wifi station sample provided.
When I made it in the previous version, I created the configuration, and...
Hi,
I am adding out of tree sensor driver (LDC2114) to nrf9160dk, I follow the Adding an Out-of-Tree sensor driver to Zephyr - Golioth . But when building the configuration...
Hi,
we have created a led driver for ucs5603.c taking reference of ws2812-spi.c. we are using nrf52840 with NCS v17.0
we have set SPI clock frequency at 1MHz and we are...
Hi,
I am trying to write a hex file created by building with the nRF54L15/CPUAPP to the nRF54L15-DK, and check whether it is in DCDC mode or LDO mode using the nrfutil command...
I am using three devices in my Zigbee network:
A Coordinator. A Router. An End Device. When I retrieve the LQI data:
If both the Router and End Device connect directly...
