Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
If I am having a custom board created and assembled using a pcb maker (makerpcb, jlcpcb, or pcbway) what do I need to ensure is on the board so I can flash and debug it? I...
We have a issue about nRF9161 on our custom board.
we flash hex our board. It doesn't work very well. sometimess it work and consume about 90mA current. sometimes board...
In our project we use a SHT4x sensor connected to I2C bus of nRF5340. To lower power consumption during idle/sleep we've a power line switch to disconnect the SHT4x from the...
Hi Nordic team,
I was testing whether Zephyr's LLEXT would work on the nRF52840DK. The example can be compiled on NCS 2.7.0 and loads fine. However the final step of having...
I am working w/ the nRF5340DK, and the project mentioned here (NCS v2.5.0, nrf/samples/crypto/rng). I was able to build/flash the project.
I wanted to verify whether the...
Hi,
I am getting to grips with the device tree and when i add an over lay file to the project, the 'new' devices are flagged with the waring that theyre being over ridden...
Hi,
using nrfutil pkg to generate the settings.hex file for the DFU is exceptionally slow on my M2.
I'm using what I believe is the latest version
nrfutil 7.5.0 (063f665...
I have an i.MX8 arm linux system running an OS based on yocto, with an nrf52840 connected over USB. The linux system receives nrf52840 firmware as part of its OTA, and updates...
Hi there,
Currently, I'm working on a solution where I need to design a software UART through emulated GPIO pins for nrf52833.
The requirements are that, solution would...
Hi all.
hello everyone . I have a project on the nrf52840 board . The wiring of the board is shown below . The module is correctly flashed , but does not start . As if it...
Dear Support,
I was working on refactoring the project and changed a majority of cmake files to improve the architecture of the project but when I finished I found out that...
Hello. "zephyr/samples/drivers/adc/adc_dt" example sample added an additional adcpin.
When reading the sensor value connected to AIN0, the value of AIN1 is also changing...
When I used the code to get the RSSI values for different channels, I found that it was very time-consuming, about 400-500ms, and most of the time was spent waiting (NRF_RADIO...
Hi.
Please tell me if it is possible to realize such a connection scheme?
I want the Dongle to act as an intermediary for data transfer from the custom board to the smartphone...
Hello,
I am experiencing an issue with my nRF5340. When I try to configure my nRF5340 using the Quick Start in nRF Connect to load an application, I encounter a problem...
