Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I have a mass storage that format a fat_fs volume and create a file when I plug the device by USB. Here is how I create a file :
It works fine, and I can see my...
Good morning,
I am developing my Zephyr solution with a Supported board RAK4631 in a RAKWireless solution called Wisblock. This is a kind of building blocks called Wisblock...
Hi,
I have the unfortunate task of needing to update a significant amount of inventory (several thousand units) using BLE OTA.
The devices are using the nRF52805 with...
Hello, I am currently developing a program that uses two SPI interfaces with the nRF5340DK. I want to use SPI3 and SPI4 for two different modules. SPI4 works fine and I can...
There are some fields that I wish to change. I am using the project direction_finding_connectionless_rx as a base to work with. I would like to be able to read and write specifically...
uart:~$ wifi_radio_ficr_prog otp_write_params 0x120 0xff63ec4f 0x9fff OTP Region is open for R/W Invalid MAC address. MAC address cannot be all 0's, broadcast or multicast...
I have a device on my desk that performs the data transfer I need, so I know it's possible. I've attached a screenshot of the successful data transfer.
I tried to replicate...
I have two toolchains and two nrf SDKs installed. v2.4.1 and v2.6.1.
I could change the toolchain used from vs code extension, but I couldn't change the west workspace....
I have been sitting with this problem for almost 2 weeks and have tried alot of different thing but without anything working,
Im using VS code with the nrf9161 and it has...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
I am using mbedtls to parse a certificate. The code is as follows:
It builds successfully but when I flash I get the following error:
Failed to parse certificate: -9774...
I'm trying to setup so that I can do firmware update on nRF5340 using only the internal flash. Due to the many dependencies between different images I'm creating my custom...
hi support team,
i was tesing homekit ncs2.5.3, with iphone se ios18, pairing failed, and i use another two iphone 12, they all succeed.
i can't see why the ios would...
USING THE PERIPHERAL_UART TO CONNECT WITH THE MULTIPLE CENTRAL DEVICES . I MODIFIED SOME CODE AND ADDED THE CUSTOM DATA WHICH IS HAVING THE 5 BYTES. WHEN I USE TO FLASH THE...
softdvice : s132
SDK version : nRF5_SDK_17.1.0_ddde560
Hi
In the project I'm working on, I need to store 3 bytes of usage time information. So I need to store data...
