Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Greetings to everyone,
The initial data are:
- nRF9160, Hw2, Fw_2023-10-26_1fae141f,
- AT%XSYSTEMMODE=1,0,0,0,
- the device works as expected with the RLC AM.
...
Hi all,
I'm unable to flash my nRF52840_XXAA using the nRF Connect extension in VS Code. My project uses the command:
west flash -d <BUILD-DIRECTORY> --dev-id 1050304532...
Hi, We tried by changing the Tx Power in nrf52840 through the register values as mentioned in the document nRF52840_Product_Specification_v1.10 and Page no 636, but it is...
Hi!
We are in the process of certifying a product using an nRF52840 against EN18031-1 (RED Cybersecurity) where we need to answer details regarding generation of cryptographic...
Hi Is it expected that after calling bt_unpair function disconnected callback is called ? I can't find any information about this behaviour in Zephyr documentation.
Hi:
I'm nRF52832 user from China, tried to download nRF_DeviceFamilyPack of MDK from http://developer.nordicsemi.com/nRF51_SDK/pieces/nRF_DeviceFamilyPack/ failed, i simply...
Hi
I am using nrf Connect sdk 2.9.0 Visual Code IDE.I have added the following configuration in the prg.conf file:
But still I am not asble to receive more than 20 bytes...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader.
I had a mucboot setup that fitted...
I have a modified asset_tracker_v2 running with SDK 2.5.0. It is connecting to AWS and sending data perfectly. It has been running for several years without a problem. I am...
Hello,
I’m running the AWS IoT sample on nRF9160DK v1.1.3 using nrf-sdk and toolchain v2.9.0, modem v1.3.7.
Everything works fine when following the instructions with...
