Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am using nRF5340 Audio DK devices. I am programming two (2) devices as 'Gateways' and one (1) device as a 'Headset'. I have two questions related to this matter...
Hi,
My project (under embedded studio )works if running on a chip with the register FICR INFO.VARIANT = 0x41414330
but freeze on a chip with the register FICR INFO.VARIANT...
I can't flash/write my nrf52840 Dongle under Linux with nRFConnect v3.9.1 with Programmer v2.0.1
The buttons remain greyed out, the left window does not display any information...
I'm following the heart rate sensor example in the VS Code Youtube Tutorials series, and there are some pretty straightforward prinkt statements in main.c, such as 'Bluetooth...
I'm getting data from peripherals, and I need 96KB/S to get to the NET layer, because the other side needs to use data in real time, but the data transfer is too slow.
So...
I have been working with multi-sensor example of ZigBee to develop it in zephyr. every things went well of endpoint sensor except that the coordinator suppose to receive the...
Hi,
I am facing issue at ble_stack_init() which internally calls sd_softdevice_enable(). I get NRF_ERROR_SVC_HANDLER_MISSING at sd_softdevice_enable() return value.
...
Hi,
i use the nRF5 SDK for Thread and Zigbee v4.1.0 , the s140 an the ble_thread_dyn_proximity - example.
I want to use the LESC encryption of BLE (in addition to Thread...
Can anyone help me with this:
I'm trying out the 'threads' sample under Visual Studio 1.8.0. Not having much luck. I'm a newbie and have followed the Video tutorials to...
Hi,
I am currently using an audio board utilizing the nRF5340 MCU. I would like to enable the BT_SHELL to use the Bluetooth command Shell, may I know how I can achieve that...
Hi,
I'm trying to measure the power consumption of Zephyr's iBeacon sample (zephyr/samples/bluetooth/ibeacon) on the nRF52840 DK. I prepared the DK by cutting the PCB track...
I use nRF52840_QIAA for design, now I need to provide ROSH of this model, I found it on the official website, please help to provide it, thank you very much!
Hi all,
After Licence request I got email with Key.
Segger Embedded Studio 4.12 accepted this key but SUA expiration date is not valid, there is just red cross and no...
Dear ,
I'm using nRF52832 to do some 2.4G communation without softdevice. Now i need to update firmware with mybootloader.
Is there some mathod to do the vector table...
Dear Team,
I am working on real time clock with the help of : github.com/.../nrf5-calendar-example but in this when do the power on and off so again start from starting...
