Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
i have created custom BLE service/characteristic using this ling https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
So, here i am able to transmitting...
Hi,
I tried running the "chat" example on two NRF52833DK boards, one as a sender sending a "Hello World" message every 500 milliseconds, the other as a receiver, and found...
Dear Support
I try to use Watchdog on nRF9160 DK.
I found the sample ..\v1.5.1\zephyr\samples\drivers\watchdog
From there I add to my prj.conf
CONFIG_WATCHDOG=y CONFIG_WDT_LOG_LEVEL_DBG...
Hi,
I wanted nRF5340 capable of reporting the VDD under-voltage event causing a pin reset through a dedicated voltage monitoring IC. For this reason I put a Flip-Flop for...
I am currently experimenting with moving my request for PSM mode into the "lte_lc_init" routine so that it is configured before the modem is moved to Normal mode.
With...
Hi!
I have previously tested connecting the nRF9160-DK to an external MCU to act as an Serial LTE Modem as per the application description. And it worked
fine. Since then...
Hello.
I use nrf9160 and download ota with aws.
After my board download successfull and return event FOTA_DOWNLOAD_EVT_FINISHED, I do system(0) to reboot.
But it can...
Hello,
what is the raw frame to get a good NRF Temperature Service UUID BLE ?
I didn't get custom data (temperature), just the service uuid 0x1809
Here is my raw frame...
Hi
Since a recent Android security update, I am experiencing issues with my 'Just Works' device based on NRF52832. Prior to this Android update, once paired, I would receive...
I am trying to connect ,disconnect and connect using nRF dev kit with one of the BLE product. (using PC-BLE-DRIVER-PY)
Steps:
1) Open driver connection:
self ...
hello Nordic
i am using nrf52832 soc, sdk 16.0, s132 v7.01
my app requires the s132
i am trying to understand the bootloader issue, not so successful on that unfortunately...
We are developing a product based on nrf52840. The product will always be configured as a BLE peripheral. We need to be able to use OTA for both SoftDevice & Application code...
Hi, all
I'm going to develop a crypto application, and tested on nRF52840 with nRF5_SDK_17.0 CC310 run-time library.
there are a need is compute public key from a known...
