Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi All,
I am working on nRF52840 and using SDK 3.0. A developing product that uses a thermostat cluster.
I want to add a few custom ID's to the thermostat "enum zb_zcl_thermostat_attr_e...
Hello All,
I am getting an assertion as below,
<error> app: ASSERTION FAILED at ..\nRF5SDK1702d674dde\nRF5_SDK_17.0.2_d674dde/components/libraries/pwr_mgmt/nrf_pwr_mgmt...
Hello,
We are trying to use `nrf_modem_lib_shutdown` to turn off the modem before entering system OFF mode. We are using LTE link control, with the following LTE settings...
I am using the nrf52832 with softdevice s112
is the app_timer library still limited to the max period of RTC1 as explained in this post https://devzone.nordicsemi.com/f...
I seem to have this issue on this page in the info center https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.0/group__nrfx__saadc__v2.html
when I click on "API description...
Hi, Dear Nordic & all:
I just want load and run the “serial_lte_modem” example about NCS 1.5.0's project in SEGGER(no file modified) on nRF9160 DK，but there is something...
Hi!
I just wanted to try out the online power profiler. It seems like it is currently not available.
Is this the correct link still https://devzone.nordicsemi.com/nordic...
Hi
testing with thingy91 v1.4.0, firmware 1.5.1.
I never succeeded to enable passive mode of nrf_asset_tracker_v2 no acceleration is detected.
Someone experience the...
Hi,
I'm new to use nrf52832, just as I said above, I want to know if the version of softdevice support bluetooth 5?
Where can I know these information?
Hello,
I've recently been porting a program over to Zephyr and hoping someone here might be able to shed some insight on this issue.
I can't seem to get flash_write to...
Hello,
I want to test a peripheral that uses private address resolution. I would like to set nrf52 eval board used by the nrf Connect Desktop to use a fixed, private random...
Dear Nordic engineers
I recently encountered a problem while developing the program of nRF52833.My program is developed on the basis of nRF5SDK 16.0, using S140 softdevice...
Hi, We recently made a custom board for a new project, based on the nRF52832-QFAA. Everything looked fine in the first place as the nRF is perfectly recognized on a PC and...
On the Eval board layout, the 2 nd and 3 rd layer cut away under the RF trace. That make the substract height equal to 57.87 mil.
For 30 mil width trace, the impedance will...
