Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports only Dual Bank DFU. This...
Hi,
I'm working in the asset tracker v2 project and currently I need to do a simple hex to char array conversion. This entails using sscanf. However the use of sscanf consistently...
Hi, I am trying to expand on the ESB PRX example and want to recreate functions with the same functionality as Arduino's micros() and millis() functions. I'd like the following...
Hello, Nordic & all:
I have a problem when use P0.21 as the libuarte's uart RX( base on libuarte example/sdk17.0.2) for my custom nrf52840 board， I looked up the reference...
We just received a PPK2 and have used it in several configurations to test a custom nrf52832 board that runs on a 3v lithium coin cell.
When connected in the following manner...
Hello:
I am working on an application that uses a simple UDP socket for transmitting data. I would like understand the zephyr BSD socket behavior when there are cellular...
Hello,
I see a number of threads on the Nordic devzone where people are asking about official support for a DFU bootloader that combines BLE and UART for transports. Most...
hello Nordic
i am working with nrf52840, SDK16.0, s140 (maybe i will change softdevice later)
i build a project on the peripheral blinky example, i change the advertising...
Hello,
My application is based on the example "ble_thread_dyn_mtd_coap_cli" (nRF5_SDK_for_Thread_and_Zigbee_v4.1.0). I would like to be able to send large files via Bluetooth...
Setup -
nRF52840-DK
Nordic Connect SDK version 1.5.0
Sample - nrf/samples/peripheral/lpuart
Commented out "uart0" in the board specific overlay
Uncommented console...
Hello i'm trying to compilate the project secure_bootloader_ble_s132 but i'm having issue with micro-ecc.
when i complie on keil the bootloader exemple i get this error...
Hello,
As the question shows, how to add RTC function to a 5340 empty project?
condition
ncs:1.5.0
board: nrf5340dk
I have found a project,but it's 52840.
...
Hello,
My application runs in non-secure mode on the nRF9160, and I would like to disable external access to CPU, RAM and Flash.
I understand this is done by setting the...
Hello
I have board nRF52833 and i have several questions:
1. Is AoA example available ? I would prefer to have example of software for tag and for the localization...
On a custom board based on nrf52840.
We want to implement OTA DFU with radio (not necessarily BLE, e.g Serial 4G Modem)
We already checked the Serial DFU example and made...
