Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
We are using this combination of software:
Mesh SDK 4.2
Bluetooth SDK 17.0.1
Softdevice 7.0.1
Mesh DFU using the precompiled bootloader binary mesh_bootloader_gccarmemb_nrf52840_xxAA...
Dear sir,
Our code gets compiled using command emBuild.exe For programming NRF Connect Programmer tool is used.
I get following error while hex file is added to programmer...
HI All !
Hope you all are doing well !
I have a question regarding "Exporting Segger Embedded IDE Project/SDK to Arduino IDE or Vscode Studio" The Reason i want this is...
Due to some error, I lost 2 factor authentication key on my other account and cannot login from there. I want to recover that account or delete it. Please help.
There is no category for this problem. But the devzone has great information but a horrible user interface riddled with headaches.
1. Pet peeve #1: Trying to enter tags...
Hi,
I'm trying to evaluate the new Asset Tracker v2 example with a Thingy91, nRF cloud, and the supplied iBasis SIM, but when I build I get the following error:
C:/Nordic...
Hello,
in documentation of nRF9160 RSRQ is defined for 0..34 and 255.
What about values 35..254? Is it possible to get these values from the chip?
I have to know, if...
using any example with BLE I get the following:
when loading , prints on log :
[00:00:00.291,595] <wrn> bt_hci_core: ECC HCI commands not available
and when I...
Hello, Nordic.
I'm configuring a mesh network. The provisioner, client and server all going well, except for one problem.
I made a client and server based on sdk-coexist...
Hi
I connected EEPROM and RTC to nRF52832.
The interface is TWI.
I'm looking for a sample program to evaluate this EEPROM and RTC.
EEPROM wants to read, write, clear...
I am going to programme the nrf52840_pca10056 DK with Arduino IDE. I was folow this tutoriol https://how2electronics.com/nordic-nrf52840-advanced-bluetooth-5-arduino-ide/...
Hi,
I am trying to set up a bootloader using the example code given in SDK 15.3.0. I am working with the nrf52840 dk and have been using the same device with the same project...
We are working on requirements for a design based on the nRF52832. Does Nordic have characterization data to share of the temperature dependency of clock drift of LFCLK?
Hello all,
I've got a Thingy 9.1. I've successfully built and flashed the serial_lte_modem example (with no changes) onto the device but when I open the serial port in LTE...
