Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello All,
I am using nRF52840 Dev-kit and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK. So far in development, I have used the GPIO edge triggering method to detect...
hi support team,
i just tested http_application_update project, and i set up one server on cloud:"106.12.30.214:32500",
also you can reach this file server from web...
Dear Team,
We are developing an Vibration Sensing System, it contains nodes and gateway where all the nodes and gateway are present in the secured mesh network.
And...
Hi,
I'm using two boards with nrf52832 and sdk 15.3.0. One alter the ble_app_mult_uart__c example as ble center ，the othe alter the ble_app_uart example as ble peripheral...
Hi,
I'm testing heart rate measurement example with my nRF52 DK. In the nRF connect application, I see the logs are converted from Hexadecimal value to user-readable values...
Hi,
I was following the example posted on the below link.
https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial...
Is it expected that the MQTT API does not receive any events unless a message is published to the server? I'm noticing that without a ping event or any message transmitted...
If I have a version 1.00 of my application which stores data in using flash data services . I make modification and version 2.00 of my application is a page larger.
1A)...
Maybe this is just a little nuisance but is there a difference pynrfjprog and nrfjprog ? There is no documentation on nfrjprog !
Searching infocenter for nrfjprog reports...
Hi,
trying for a few days now to generate a DFU zip file from the blinky example on a PCA10056:
nrfutil pkg generate --hw-version 52 --sd-req 0x9A --application-version...
We are in QA phase for launching the product. Our firmware is based on SDK v1.2 of nrf9160.
With the firmware, we have already tested the process in which the device is...
Hello!!
I am using transmitter example on my custom board having 10 buttons. I want to minimise the power consumption as it is powered by coin cell. I have used below tutorial...
I have been researching a variety of wireless tools that involves the use of Bluetooth module and signal manipulation and came across nordic semi after coming across a few...
