after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I am trying to perform an OTA DFU of SD + BL on nRF52840, upgrading the SoftDevice from 6.1.1 to 7.0.1.
I have been able to do a DFU of application only, and it works...
Hello everyone. I have the following issue: I would like to connect some Nordic Thingy:52 nRF6936 devices in a mesh network, using the application nRF Mesh . In theory, the...
Hi,
We are in the development stage of a project using NRF9160. We would like to know which one is the stable version of NRF connect SDK. In the , git we can see tags like...
I have a non-secure app targeted at the nRF9160-DK platform and use SPM as the secure app. I can apply a device tree overlay to SPM to enable peripherals from the non-secure...
Hi,
We are creating an application that requires LTE connectivity, GPS and communicating to a server using HTTPS. We used the HTPPS client example as a starting point and...
Hi,
I'm quite new to the nRF environment and am trying to run one of the nRF5 SDK examples (ble_peripheral -> ble_app_uart -> pca10056 -> s140) on a custom bord with BT840...
Hello everyone, I have a problem I am trying to merge to project using I2c and Uart, So I copy the code from the uart example in the sdk.
I can read on the debug terminal...
Good afternoon, I am trying migrate from ARM compilar 5 to 6 some examples of the SDK 16, but i have some problems with it. I was wondering if a version 6 compatible sdk would...
Hi
I am using the provided example ble_app_queued_writes to send 256 bytes in each call.
It is taking around 13 seconds to transfer 3136 bytes:
12 calls of 256 and one...
Hi,
My project is currently using NRF52832 with Mesh 4.1
After update from SDK15.0.0 to SDK17.0.0, everything just works fine except my button.
I am using P0.18 for...
Hi,
currently we are developing a firmware for 52840 based on the nRF5 v.16 SDK with Softdevice 7.0.1 on a custom board. We are able to connect and bond up to 5 devices...
Hey all,
I have a custom board running nRF52832 with Softdevice S132 v6.1.0 and SDK15.2. My application requires me to start advertising without any manufacturer data...
Hi
in our device, HFXO is running permanently. There is an external LFXO running permanently as well.
Now I'm wondering what would be the additional current draw if we...
