Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi
I just want to read the Device Information Firmware revision string from a known Peripheral on my Central.
I Use the PCA10028 with SDK 12.3 and Softdevice S130...
Hello to all,
i've developed some application under 3.2.0 SDK. Now I want to port my application on new 4.1.0 SDK but a I have found a relevant issue.
Before migrating...
In section 6.3.2 of the NRF52840 dongle user guide it describes how to modify the board for use with an external, regulated power supply. Once those modifications are made...
In order to implement the central roll, I put ble_app_uart_c on ble_app_multilink_central and joined them to communicate with the pc.
What I did
1. Add enable in ble_app_uart_c...
Hi ,
I need to start my application using sdk5 16.0 version, which should have custom ble servivnced and dfu feature.
After getting some trouble with zephyr os, i decided...
I have used an example in the sdk 15.2.0 Pin_change_int_pca10040 and added 2 header files and 2 C files extra to this project. I have cleared all the error which came while...
Our hardware has Winbond NAND Flash chip connected to the nordic MCU(nrf52840 /nrf5340). However QSPI cannot be used as nordicSDK doesn't support NAND Flash.
I understand...
Hello,
I am using the Power Profiler Kit connected on top of an NRF52840-DK
I am using IAR and using IAR's J-LINK plugin to program/debug an application on the DK. However...
I am trying the example project ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\l ight_switch' and ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\ dimming' available in nrf5_SDK_for_Mesh_v4...
Hello,
I'm experiencing NRF_ERROR_INTERNAL from a call to pm_peer_new(). While further investigating into this, it turned out, that the p_bonding_data parameter was checkt...
Hello! If possible, I ask you to answer a practical (technical) question: how long does a typical process of establishing a communication session (“handshake”) in the BT5...
Hello, we are creating a device on an nRF52832. I started our project based on the examples/ble_peripheral/ble_app_uart project, which worked fine. However, I needed to modify...
Hi,
I'm using the latest master branch of nRF Connect SDK and I'm having problems with building my project after the commits of the past few days. I went to check what have...
Describe the bug Compilation error when CONFIG_BOOTLOADER_MCUBOOT=y or CONFIG_SECURE_BOOT=y specified
To Reproduce Steps to reproduce the behavior:
go to zephyr\samples...
