Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am working on temp. sensor with nrf52832 dev kit for firmware testing and development and also using nrf52810 for product testing.
in my code, I merged twi communication...
hi,
I want to develop a project based on ble beacon mode and ble app hts code.
and I am using nrf52810. so will it work if I merge both codes and use for this project...
I know that nrf_cal_set_time() from the nrf calendar example is NOT meant to be called on a regular basis / should only be called to update the time being kept locally to...
Hi,
We are looking for a guideline to trigger GPIO and SAADC sampling at the same time.
Our purpose is to sample every 20 m
Hi,
We are looking for a guideline...
Hi, We have a DFU OTA process that was functional, but updating our softdevice to s113 7.2.0 has left us with a problem - since the softdevice does not exist in the nrfutil...
Hello.
I am doing a small project where nrf52 reads data from a BME280 temperature sensor via SPI and sends it using ESB.
I have no experience with radio, so I use a ready...
I would like to use the NRF24L01+ from a 3v coin cell, but interface it over SPI with a 1.8v-powered microcontroller. Assuming the uC is tolerant of the NRF SPI outputs, I...
We have a application where data transfers happen through a mechanism where the external client does a write-without-response to send in a command. The response to the command...
I am busy with my first BLE project , programming a custom service for both pheripheral and central role. I have already finished the pheripheral service, using a custom service...
There are other GPS modules on the market which can give information like "the device is within 10 meters of the given coordinates". Is there a way to either get this information...
Hello,
i am using AES CCM encryption available in nrf52832,
my data which need to be encrypt is same every time. data will encrypt and 4 byte will add at the end of...
Hi all,
I am working on a project with the nrf52832 and I am using softdevice S132 6.1.1. After creating my desired flash layout (with some help on this forum, thanks!)...
Dear,
I am using NRF52840 and nRF5_SDK_17.0.0_9d13099 and SES development tool.
And also, I am testing SPI master with p0.29/30,31 and P0.26.
but when I do "nrf_drv_spi_init...
I am tring to DFU by Bluetooth with example, but it not work.
Please someone help me!!
My environment
PCA10056 nRF52840
SDK17.0.0
examples/dfu/secure_bootloader...
I was working with the Thingy:91 trying to get into into a serial printing state. I tried to updated the modem and firmware using the nrf Programmer. When updating the modem...
