after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
software: nrf5_SDK_for_Mesh_v4.0.0_src
hardware:nrf52382QFAA
I just build the sdk,and then download s132_nrf52_7.0.1_softdevice.hex and light_switch_provisioner_nrf52832_xxAA_s132_7...
Moved to a new machine and now can't debug. I suppose I've overlooked something. First, Segger doesn't recognize that it has just compiled the app and asks to recompile. Then...
I've been looking at ways of implementing Web Bluetooth to connect to a Thingy52 using Bluetooth Low Energy.
https://github.com/NordicPlayground/Nordic-Thingy52-Thingyjs...
Hello; I have been working with nrf52840 dk's for the past couple months, and came across a few questions.
First off, my temporary goal using nrf52840 is to send a timestamp...
Hi
I am planning to use the nRF52833 for the AoA direction finding application. On that I had two questions.
1. Currently I have two nRF52833 DKs for transmission and...
Hi all,
I am developing on nRF Mesh SDK 4.0.0 with nRF52833 DK (PCA10100).
To save/restore persistent model state to flash, I added the code using mesh_config_entry_get...
Hello,
I'm new with the nordic chips and SDK and have a short question: I'm trying to send the battery capacity of my BLE device within the advertising data. I found some...
Hi
Do you have any example code to support OCF standard and/or IoTivity (Lite).
Or any plan to support IoTivity?
(We're targeting OCF supported device with nRF52832...
Hello all,
I am running "ble_app_beacon" example code in nrf52832. when i'm using samsung and honor mobile phones the nrf Connect application is not showing the beacon,...
I'm trying to enable the CMSIS Wizard on SES 4.42a. I followed the instructions and pasted the required xml into tools.xml, saved the file and restarted SES.
This is my...
Hi Support,
I need to use another eSIM not the iBasis, because the company those not have roaming coverage in Bulgaria.
Question: If I use a IoT eSIM card Telefonica...
I want to send a one byte payload from the nrf24l01+ (Sparkfun dev board), to nrf52840 DK using the example esb_prx. How should I configure the nrf24 registers to make this...
We have run the Hello World program on the nRF5340-PDK, but now following the basic steps to program the heart rate example, there is no BT broadcast for Zephyr Heartrate...