Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have the debug section of the evaluation board turned off, modifications to measure current with a DMM set up, and am using a keysight 34465a DMM to measure current. The...
Here is the code snippet initializing the Heart Rate Measurement Characteristic in the BleHeartRateMonitor example:
static uint32_t characteristic_init() { uint32_t error_code;...
When using nRF Connect and 52840 Dongle, the normal BLE scan app works fine but connecting to the RSSI ap, the reprogramming of the dongle fails with timeout.
Hi,
I have nrf9160 DK.
I found there is u-blox driver available. Is it possible that the 9160 modem can be added an interface as a modem using u-blox? If so, there is...
NRF_LOG_RAW_HEXDUMP_INFO() is not printing complete Extended Advertisement data in HEX format. It just prints first 80 bytes of whole advertisement packet.
I added below...
Hi Nordic Developers,
Service Discovery Protocol (SDP) is a protocol for Bluetooth to detect the service nearby and to determine their characteristics by using UUID.
I...
Hello!
I am trying to lower the sleep current of our custom board. Right now in sleep, the whole system have a current consumption of 100uA. There might be component choices...
I get answer from msromero that If zigbee network is open, then new zed can join this network.
What means that nework is open ?
I want zigbee netork is silently joinable...
HI, i would like to get device name and print to uart, but when i try to print the device name i got error character.
Here my snipet code and uart result
Hi.
My target device is nRF51822 and SDK version is 12.3.0.
I try to add Device Information Service to example "ble_app_uart_pca10028_s130"
---------- main.c (added...
Hi,
I am using NRF52832 sdk 15.2.0.
I am trying to do a device firmware update by following this link: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting...
Dears
I listed my questions below. Thanks.
1. About GPS searching and fixing, I tried Thingy91 outdoors.
- When Thingy91 connected to LTE, did LED shall blue color?...
I have a nRF52810 project which initially used the ble_peripheral/ble_app_hrs from the enRF5_SDK_15.3.0_59ac345 as a starting point. I have changed to a custom service and...
I am programming using the glucose service example source. The example source does not send any context data, so I added However, when testing with nRF toolbox, I noticed...
