Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am interfacing My acc/gyro sensor (ICM-20648) with nrf52832. I am using my custom board and successfully get the mac address of my custom board. Noe i need to ensure about...
I use two PCA10040 for nus experiment, S132, SDK14.1
sniffer capture packets found that no data can be captured after the master send CONNECT_REQ, I guess it is not because...
Hello,
I have a working application on nrf52832, running sdk version 15.0 and SD132 version 6.0.0. Now I would like to add dfu functionality. I followed the instructions...
I followed this :
Connect the nRF5 boards to the USB ports and decide which one you want to use as a client and which one as a provisioner by noting down their 9-digit Segger...
Hi all,
I want to verify nRF52840 SoC SPIS peripheral on PCA10056 DK using any compatible SPI master hosts. I use SDK v15.2.0 SPIS example.
I know that Nordic SPIS peripheral...
Hello All
I'm trying to lock debugging/reading capability in my code. My system consists of a bootloader and an application beside the Softdevice and MBR.
What is already...
For simplicity, I extracted the Demo 1 routine from the "pwm_driver" example which has 5 demos 'cause I thought it is simpler.
The code is shown below:
Can you please...
Hi, i want to build my ble app with softdevice. A s a result, I want to have a single .hex file that contains the sofdevice. And i am going to flash it to the nrf51822 using...
I have PTR9818 module and NRF52840 Development Kit. I flash firmware CLI example(SDK for Thread and Zigbee 2.0.0) for PTR9818 module and communicate with PC use USB-USART...
Hallo,
Currently I'm investigating different Low Energy Bluetooth solutions for our healtcare products that we build in Televic Healthcare.
So here is the setup I...
Hi all,
I'm a little bit confused with the Thingy52 SDK.
The "ble_app_thingy_s132_pca20020" code is the same of the "thingy_v2.1.0.HW_1.0" precompiled hex file?
Thanks...
Hello
I would like to know GPIO leakage current, especially when the GPIO outputs Low
state, leakage current flow thorough the High side MOSFET parastic diode.
If nobody...
