Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello, I want to establish wireless connection between PC (windows) and nRF51DK board. I want to send data from the sensor connected to DK every 200ms to the PC.
My question...
Hi,
Our product is peripheral device which is based on nRF52840
We also develop central device on PC application (windows 7 & 10) but our customers might use BLE 4.2 ...
Hi Nordic. I am working on a project, where I have to connect to a peripheral device with the NRF52 DK as a central device, and get services and characteristics from the peripheral...
According to the documentation of the softdevice v6.
The scanner will automatically stop in the following cases:
sd_ble_gap_scan_stop is called.
sd_ble_gap_connect...
Hey everyone,
I use Bluetooth Mesh 2.1.1 , SDK 15.0, and nRF52840
I want to change the Transmit Power of my Beacon-Server (Mesh Advertisement Packet) on the fly, for example...
Hi everyone,
My hw/sw configuration:
- nRF52840
- sdk 15.0.0
- softdevice: s140_nrf52_6.0.0
I need to use 2 SPI and 2 I2C interfaces.
Nrf52840 has
- 3 SPI (spi0...
I am using SES and I tried to open and build this example -->
C:\nordic_semi\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_proximity\pca10056\s140\ses\ble_app_proximity_pca10056_s140...
Hi Great Nordic team:
As title, when I perform white-list function in BLE connection,
Is there any way to know from peripheral that there is a connection request from...
Hi,
I have a project that I have product which I have produced several thousand over the last couple of years and today find an issue.
The product has a receiver that...
Hello,
Device: nrf52840DK
Software: nRFgoStudio (version 1.21.2.10)
Operating System: Windows 10 (updated)
I am not able to enable the reset pin. I am trying to...
Hello All,
I am trying to build the "bootloader_secure_serial" example from SDK 14.2.0 on IAR Embedded Workbench IDE ARM- 7.60.1 and I get this error: Error[Pg004]: macro...
Hi,
I'm trying to utilize PPI system to generate repetitive sequence of tasks (lets call them Task A, B, C, D, E, F) at 0,10,20,40,60,80 ms every second. i.e. I need to...
Hi,
I'm trying to test adding my own custom service, but have errors when I tried to add a 128bit UUID, the test code is simple, in the service_init() function, I just added...
I am using nrf52832 and sdk 14.2.0.The software I am using is keil 5.17.the error is as follows:.\_build\nrf52832_xxaa.axf: Error: L6915E: Library reports error: __use_no_semihosting...
