Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
It's said that timer0 is used by softdevice and the current consumption differentiates for the defferent timer frequency (PS V3.1 table 22 and table 52).
But I don't find...
Hi,
when using a test based on the UART app, when running it a samsung all is working just great.
However, I tested it on a Nexus 7 with less luck.
From the Sniffer/wireshark...
Can anybody recommend me to select chipset providing following functions?
BLE (Bluetooth smart)
SPI Slave
No need external MCU
UART for debugging (optional...
SWD is supposedly a multi-drop bus.
Is there a way to program multiple nRF chips using only the 2 SWDCLK/SWDIO pins?
How are people programming and verifying boards...
i compiled the ble_uart_exmaple program and it get downloaded to the kit then the four LED on the nrf51DK started blinking continously i dont know what happen to board and...
Hi,
I have a question regarding sending sensor values from a slave to the multi link central. I am using a custom profile on the peripheral to send sensor values as notifications...
I use softdevice s110 7.3.0 and SDK version 7.2.
Some times softdevice call app_error_handler with:
error_code 0xDEADBEEF
line num - 990
file_name - src\ll_ctrl.s0.c...
Hi,
I try blinky with softdevice example and reconfigure it to support nRF51822AA. I can program my custom board, I can debug as well, but led is not blinking. I have connected...
Hi,
I want to set the advertising interval to 10.24 sec.
I changed the value of APP_ADV_INTERVAL to 0x4000.
But when i try to discover my device using MCP, it is not...
I'm trying to track down an intermittent bug in programming our Nordic board. So, I'm having to laboriously reconstruct the SWD transactions and understand them.
A transaction...
I use nRF51822 Model in my project that I need to run bluetooth advertising all time. And when I measured current, I found 1mA that is not enough to run for 1 year by just...
Hi,
My project include two MCU with n51822 and STM32. I expect upgrading STM32 application firmware by n51822 DFU function. Do you give your advice to implement it by modifying...
Hi All,
I am struggling getting my N548 module to transmit any ANT+ ...
I have tried the Cycling Power Sample Application (S310)
And the Cadense / Speed (S210) Sample...
Hello,
Is there any delay between when the reset pin is driven low and the actual reset of the chip. Would it be possible to sense the reset pin and perform some quick...
I am designing an nrf52 based device running at 1.8V. To debug the device I was planning to use debug out option of the nrf52 preview DK. However, I just find that, the debug...
