Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am trying to setup the hrs sample with gcc (4.8.3) and Eclipse Kepler but althoug it compiles fine the editor is complaining about:
Symbol 'softdevice_evt_schedule' could...
I follow devzone.nordicsemi.com/.../can-nordic-please-document-how-to-debug-code-on-their-processors
and add retarget.c and
retarget_init();
printf("Start...\r\n");
to...
I am running 5.2 sdk's UART under experimenta\ble_app_uart,
I assume it works with www.nordicsemi.com/.../nRF-UART-2.0-for-Android-4.3
when Android app sends data to device...
Why does this simple float arithmetic cause my GDB client to hang and my GDB server to say "GDB closed TCP/IP connection"? I'm sure I've got other float operations working...
Hi,
I know the flash operation, including earse and write, should be excuted when the radio is inactive.
So, I put the flash earse and write operation into the function...
Hello,
I have Nordic nrf51822 evaluation kit. Can you tell me how can I send 'Hello, Wake up' message from Nordic nrf51822 evaluation kit (pca10001) to nrf usb dongle kit...
Im getting the following error ,when I try to compile the example ble_HID_template from the latest Arduino Nordic Release:
ble_HID_template.ino: In function 'void aci_loop...
-- When a ble peripheral starts advertising and then receives a BLE_GAP_EVT_CONNECTED event, the stack stops advertising automatically right?
-- When you get BLE_GAP_EVT_CONNECTED...
Hi
I have successfully created services and characteristic from nRFGO Studio and they are advertising well even receiving and transmitting is going well. Now my problem...
Hello,
i ported example of mouse by HID for nRF51822 to nRF51422. The device is detected as mouse by Bluetooth in Windows 7 but I cannot to connect it. Any ideas whats wrong...
Hi,
I'm wanting to develop some solutions around the NRF518222 IC. I want to try out the various modes etc, bluetooth and ANT as well as trying to get some longer range...
I try the throughput in S310,
I refer the "nrf51-ble-app-lbs" to make our code(interval is 20ms),
and test with Master Control Panel.
it seen only have 1.7KBps.
Could...
Hi,
I am trying to detect if a disconnection occurs due to a signal loss.
In the application's BLE Stack event handler, I have found that there is a disconnect reason...
