I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
I'm working on a Keyboard&Touchpad project, very similar configuration with Smart Remote 2, so I'm considering to use nRF24LU1+ as receiver's MCU. The receiver will be...
uint32_t ble_advdata_set (const ble_advdata_t *p_advdata, const ble_advdata_t *p_srdata)
If I set the second parameter p_srdata, does it mean passing encoded advertising...
Hi developers,
Just wondering if anyone has worked with a good BLE Python library that he can recommend. I have BLE peripherals that send out notifications. What I'd like...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hello,
is it possible to measure frequency from 1Hz up to 400kHz (50% duty cycle) on gpio pin having soft device enabled with Peripheral functionality? The measurement...
Hello,
I am using the RADIO peripheral to send BLE 4 advertising packets back and forth between 2 DK's (nrf52840 as transmitter, nrf52833 as receiver) following the radio...
Hi,
Nrf52 52840DK,SDK17 S140.
how to broadcasts continuous data? (Continuous broadcasting, with different data each time)
code as follows:
SDKs\nRF5_SDK_17.0.2_d674dde...
I have VSCode 1.63.0 (Universal) on macOS 12.0.1 with ncs v1.7.1 and a board with an nRF52840 MCU. I'm using the "hello_world" example. If I power cycle the board I can start...
Hi,
I'm trying to connect to hook-up a debugger in VSCode to my target but am unable to. The hardware is custom and JLink connects fine with nrfjprog to program and erase...
Hi,
I'm trying to ,create a development environment for Alexa gadget in nRF52832.
here is the thing which I'm using:
1. nRF connect for desktop version v3.9.1
2. Toolchain...
I had a Thingy91 that I think I bricked in trying to upgrade the firmware. I'm able to see the device in desktop programming, but it says erasing then gets to a 100% screen...
Dear, I am new to Nordic. I created a simple project for testing. There is a small fucntion to display "Hello World". After , Re-build Solution.. the memory used is as shown...
Dear community,
I am evaluating the nrf52 chip on the nrf52dk. I am using the peripheral_uart example, built for nrf52810. I have stumbled upon an error which I'm not sure...
In our BLE connections we often receive a BLE_GATTC_EVT_WRITE_RSP event with gatt_status 0x01F2.
Looking at the list of GATT_STATUS values, this must be an error in the...
Hi, based on my previous posts ( 2nd post , 1st post ) regarding the ble_app_uart_c multilink example I now face another issue.
When I run the multilink example on my nRF52840...
Hello,
Until now we compiled our company project using SEGGER Embedded Studio command line tool 'emBuild' that was called from a custom Makefile like this:
But we...
Hi all,
I want to self provision my node. I am using nrf52832 dev board, mesh SDK v 3.1.0, light switch client example. You may wonder why self provisioning, when there...
Hi, I am currently utilizing an app that supports multi link; however, I was only able to get 7 maximum stable connections. My goal for this multi-link is to connect a sensor...
