I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
The following change was introduced in v4.0.0
Note that mesh_config_clear() was replaced with mesh_opt_clear() which is a rather big change of behavior that wasn't documented...
Hi,
Just trying to run mqtt sample with TLS and AWS IoT backend. Everything worked fine in the beginning, but then after I tweaked the code a bit I suddenly started getting...
Hello,
I'm using SDK5 v16.0 and softdevice S140 v7.0.1.
At some of the PCs, it takes much longer than usual to upload the zip package. On my machine, the transfer rate...
Errata 182 needs to be applied (in revision 2 devices) to enable the fix for erratas 102, 106 and 107. The workarounds for these erratas all stated that they reduced receive...
Hi,
I am using NRF51822 SDK12 S130, I have increased my code and encountered a crash right at the beginning, I debugged it as follows -
I increase an integer ( uint32...
Hi,
I was wondering if I could get a little information on how to set a pin as High Impedance using the zephyr gpio.h library.
We have a shared pin between a nRF9160 and...
Is there a value or values range defined for the user cmd/evt in the serial interface?
I would like to use the uart for some app specific operations, and could use packet...
Hello. I'm having problems to programme the nRF52832. I'm just connecting the VCC (+3,3V), GND and SWDIO and SWDCLK. Is it ncessary to connect any other devices like capacitors...
Hello,
I have been using the buttonless DFU method for a while on the nrf52832 Chip. Due to performances need we changed the chip for our product from nrf52832 to nrf52840...
So, my understanding of the current support for a PA/LNA is a set of configuration options you can pass into a BLE library and then the soft device will handle the operation...
Hello,
I am interfacing a nRF52 based module with external flash memory.
When I try to program/read a single byte, I get the " NRF_ERROR_INVALID_ADDR" error.
This...
Hi,
I'm trying to develop a custom provisioner for a nRF52840 DK. All I've done at the moment is merely rewriting the Light Switch provisioner example.
The code compiles...
Hi,
I'm writing a central application for the nRF9160 DK. The central connects to an nRF52832 peripheral and subscribes to a characteristic whose CCCD handle and value handle...
Hii,
I am using nRF52840 module in beacon mode which is transmission one value read from sensor. According to code sensor sampling and transmission cycle is controlled by...
